Safety Rules - MARIMEX Orlando Premium Assembly Instructions Manual

the substrate so that it can not be moved without damage. Make sure that the ar-
ched seam remains approximately in the middle of the fillet (see Figures 4-15).
After smoothing the floor, continue swimming the pool and gradually smooth the foil
on the wall. Ensure that the foil is not tightened and that there is no air gap.
Gradually remove the plastic clamping strips at the top of the wall, always just one
piece and smooth the wrinkles on the foil. On the smoothed part, put the plastic
clamping strips in close-up (Figures 4-18).
After all the wrinkles have been wiped off, cut off the overlapping portion of the last
plastic bar so that its end is tightly seated on the following bar (Figure 4-19).
FOR CIRCULAR POOL: Now press the plastic bar [4] on the clamping bar. Use a pair
of flexible coupling pins [2] to connect another plastic strip [4] and follow the entire
circumference of the pool. (see Fig.
4-20). To shorten the last plastic strip, connect it to the rest of the upper frame using
a pair of connecting pins (see Figure 4-20).
NOTE: The supplied coupling pins [2] are in two guides - the pins without longitudinal
cut are designed for the lower frame, the longitudinal section pins (elastic) for the
upper frame.
NOTE: The slight ripple of the foil during installation is natural. It is caused by the will
of the vinyl material, which protects the film when it shrinks.
NOTE: The film is not a structural element of the pool. Its main function is to prevent
water from leaking out of the pool. The water pressure is held by the walls and the
construction elements of the pool. The film must adhere properly to the ground, the
filler filler and the pool wall, never carry the weight of water that could damage it.
Part 5 – Installation of upper bars and collars at the
oval pool
Identify upper leaves
The 3,7x5,5m oval pool consists of 4 6-A strips and 6 bars 6.
Continue to fill the swimming pool
a. Continue filling your pool with water while installing the top frame and the vertical
pillars of the pool.
Remove written collections and upper leaves
Attach the metal plate [17] to the upper end of the column with the inclined strut [9]
of the oval pool and the wall [30]. Align the holes in the plate and the post with one
another and screw both parts together with a pair of self-tapping screws [3] (Figure
5-2).
On the metal plate [17], slide the upper rails from both sides (Fig 5-3) according to
the type of oval pool (Fig 5-3).
Apply and align the bottom of one vertical post [1] in the round part of the pool with
the retaining part of one connector [2] (Figures 5-4). The connector tab of the co-
nnector must be outside the vertical post.
Align the bolt hole in the post and the bolt hole in the flap and attach the column
with the self-tapping screw [3] (Figures 5-4).
Place the upper clutch [4] on the top edge of the pool wall so that the flap of the
upper clutch catch part is outside the pool (Figure 5-5).
96
Insert one end of the upper bar [6] into the top clutch [4]. Align the bolt hole in the
flap and the bolt hole near the top of the vertical post [1]. The flap of the upper
clutch attachment must be outside the vertical post. The post must be in the verti-
cal position.
Fasten the upper clutch to the vertical post with one self-tapping screw [3]. The
pillar will need to be pressed firmly (Figure 5-6).
Repeat the steps for each vertical post along the perimeter of the pool wall.
AID: Use grooving on the pool wall to check the vertical posture.
Finally, in the case of an oval pool, attach a plastic decorative cap [18] to the metal
plates [17]. Apply the cover using the procedure shown in Figure 5-7. Attach the
cover with screw [19] (fig 5-8).
NOTE: The self-tapping screws [19] are 25 mm long, making it different from the
other self-tapping screws supplied with the fasteners. Only these screws can be
used to attach the cap.
Do not warm samolepk
• Stick a warning sticker near the place where you enter or exit the pool. It must
be remembered that the pool is not too deep to jump safely; there is a risk of
injury.
Complete filling the swimming pool
Fill the pool with water up to 5 cm below the lowest hole in the pool wall. Then
follow the instructions for mounting your dirt collector.
IMPORTANT: The pool may bulge or move a little while filling with water. That's
normal.
Attach the filter device to the mounted collector according to the relevant in-
structions.
Fill the water up to the level of the center of the header flange and perform the
initial disinfection of the water. This makes your pool ready for use.

Safety rules

Your pool contains plenty of water and is deep enough to pose a significant risk to
life and health if the following safety rules are not strictly observed. Those who use
the pool for the first time have the greatest risk of injury. Ensure everyone knows
the security rules before they enter the pool.
Banning Jumping to the Pool or Jumping Jumping - The top of your pool wall is
not a footbridge and must not be used to jump into a pool or jump dive. Do not
jump into the pool or jump dive in the pool from the steps or top of the pool wall.
Jumping jumping or jumping into the pool can result in serious injury or death by
drowning.
Never use the pool alone - Never allow the pool to be used unattended by at least
one person who does not belong to the bather. There must always be someone
who can help in case of danger.
Never leave children unattended - Never leave the child alone or unattended in the
pool or near the pool - for one second.
No "brajgl" - Do not let the "roar" in the pool or around your pool. Surfaces can slip
and become dangerous when wet. Movement on the top of the pool is not allowed.
At night, illuminate the pool - If the pool is used after dusk, adequate lighting must
EN
97