Positioning Speakers; Connecting The Power - Onkyo TX-DS575x Instruction Manual

Positioning speakers

TV or Screen
Sub-
woofer
speaker
Surround
speaker
Left

Connecting the power

3. STANDBY/ON button
STANDBY indicator
2. POWER switch
Display
FM MUTE /
PTY/TP MEMORY MODE
STANDBY/ON
STANDBY
POWER
ON OFF
A SPEAKERS B LISTENING MODE
DISPLAY STEREO /DTS SURROUND 5 CH STEREO
PHONES
MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3
INPUT
3. ON button
2. MODE AUDIO
button
Center
speaker
Surround
speaker
Right
Listener
DIGITAL/ SP / SYS MASTER VOLUME
DOWN TUNING UP ANALOG SETUP CH LEVEL
MODE
PRESET / MODE ADJ
DOW N UP
ENTER / SCAN
LATE NIGHT / LFE LEVEL
DSP FRONT EFFECT Re -EQ CONTROL
1.
To wall
BASS TREBLE
outlet
TAPE FM AM PHONO C D
TX-DS575X
AV RECEIVER
3. STNBY button
Positioning speakers
Speaker placement plays an important role in the reproduction of
Surround sound. The placement of the speakers varies depending
on the size of the room and the wall coverings used in the room.
The illustration shows an example of a layout for standard speaker
placement. Refer to this example when you position the speakers in
order to experience the best of Surround sound.
Standard speaker placement
For ideal Surround effects, all speakers should be installed. If a
center speaker or subwoofer is not connected, the sound from the
unused channel is properly distributed to the connected speakers in
order to produce the best Surround sound possible.
Front: The left, right, and center speakers should face the seated
listener and be placed at ear level. The center speaker produces a
richer sound image by enhancing the perception of the sound's
source and movement.
Surround: Place the left and right Surround speakers 1 meter
(3 feet) above the listener's ear level and facing toward the sides of
the room, making sure that the listener is within the speakers' dis-
persion angle. These speakers produce the feel of a moving sound
while creating the sensation of being in the middle of the action.
Subwoofer: Install a subwoofer with a built-in power amplifier for
powerful bass sounds. The placement of the subwoofer does not
affect the final quality of the sound image too much, so you can
install it with the room layout in mind.
Refer to the speaker's instruction manual for more details.
Connecting the power
Before you plug in the receiver, confirm that all connections
have been made properly.
Turning on this receiver's power may cause a momentary power
surge, which might interfere with other electrical equipment, such as
computers. If this happens, use a wall outlet on a different circuit.
1. Plug the power cord into an AC wall outlet.
NOTE:
When you use the TX-DS575X for the first time:
When the TX-DS575X is shipped from the factory, the POWER
switch is set to ON ( ). Therefore, when you plug in the
power cord to the AC outlet, the Standby indicator lights up and
the unit enters Standby mode as described in Step 2.
2. Press the POWER switch to set it to the ON(
place the receiver in Standby mode.
The STANDBY indicator will light up.
Press the POWER switch again to set it to the OFF (
tion to turn off the power to the receiver.
3. Press the STANDBY/ON button to turn on the receiver. The
display will light up and the STANDBY indicator will be
turned off.
If you press the STANDBY/ON button, the receiver returns to
Standby mode.
Turning the power on from the remote controller:
1. Press the POWER switch of the TX-DS575X to turn on the
power to the unit.
2. Press the MODE AUDIO button.
3. Press the ON button to turn on the power to the TX-
DS575X, or press the STNBY button to set the receiver in
standby mode.
You cannot use the remote controller if the POWER switch on
the receiver is set to OFF.
Set the volume level to minimum before you turn off the power
to the receiver.
) position to
) posi-
11