Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stratasys ProAero+
Summary of Contents for Stratasys ProAero+
- Page 1 Installation and User Manual ProAero™+ Air Extraction System DOC-01011 Rev. A...
- Page 2 Stratasys. This document may be printed for internal use only. All copies shall contain a full copy of this copyright notice.
-
Page 3: Table Of Contents
Maintenance ....................8 Inspecting the System ......................9 Cleaning the System ......................9 Replacing the Filters ......................9 Disposing of the Filters......................10 System Specifications.................. 11 Dimensions .......................... 11 Filter Information ......................... 12 © Copyright 2021 Stratasys. All rights reserved. Page iii... -
Page 4: Overview
Figure 1: ProAero+ front Cover Cover clips (4) Power switch Fan speed 100-240 VAC adjustment power connector Figure 2: ProAero+ rear Keep covered Air inlet Control cable switch Control cable connector © Copyright 2021 Stratasys. All rights reserved. Page 1... -
Page 5: Safety
1. Always disconnect the system from the main power supply before servicing. 2. Use this system only as described in this manual. 3. Connect the system to a properly grounded outlet. © Copyright 2021 Stratasys. All rights reserved. Page 2... -
Page 6: Fire Safety
However, it is the responsibility of the user to verify the media and filter type are suitable for the particular application where the air extraction system is being used. © Copyright 2021 Stratasys. All rights reserved. Page 3... -
Page 7: Warning And Information Labels
50 cm (19.5 in.) from another object on the side of the air outlet to ensure adequate airflow. Caution: Do not cover the exhaust outlets, as this restricts the airflow and causes overheating. © Copyright 2021 Stratasys. All rights reserved. Page 4... -
Page 8: Installation
The power outlet at the site should be located near the system. The power cable should be routed so as not to create a trip hazard. Connect the power cable to the system. Only connect the cable to the power outlet after finishing the installation process. © Copyright 2021 Stratasys. All rights reserved. Page 5... -
Page 9: Connecting To The 3D Printer
For all Objet260 and J826 printers: screw this on to the other end of the duct (counterclockwise) and connect it to the printer exhaust outlet. A control cable is supplied with the system. This is for future use. Save this for when this option is available. © Copyright 2021 Stratasys. All rights reserved. Page 6... -
Page 10: Connecting The Silencer (Optional)
3. Either push the silencer forward so it moves under the system, or roll the system straight back until it covers the lower part of the silencer completely, and is touching the higher part of the silencer. 4. Lock the front wheels of the system. © Copyright 2021 Stratasys. All rights reserved. Page 7... -
Page 11: Operation
The filter change indicator is red initially after turning on the system, and then turns green after a short while. Maintenance User maintenance is limited to cleaning the system and filter replacement. Only Stratasys technicians are authorized to perform component testing and replacement. Warning: Personal Injury Hazard... -
Page 12: Inspecting The System
Inspecting the System Inspecting the System If required by local laws and regulations, this system must be inspected. Contact Stratasys for more information about inspection and certification. Cleaning the System • Clean the exterior of the system with a damp cloth and non-aggressive detergent. -
Page 13: Disposing Of The Filters
It is the customer's responsibility to verify that the disposal of filters complies with all local and/or industrial regulations. © Copyright 2021 Stratasys. All rights reserved. Page 10... -
Page 14: System Specifications
Metric (mm) Imperial (inches) Crate: (Weight: 72 kg / 159 lbs) Height 1180 46.5 Width 26.4 Depth 19.7 Unpackaged: (Weight: 51 kg / 113 lbs) Height 24.6 Width 20.67 Depth 15.16 © Copyright 2021 Stratasys. All rights reserved. Page 11... -
Page 15: Filter Information
Filter Information Filter Information Filter Type Construction Efficiency Combined Filter Maxipleat Construction 99.997% @ 0.3 microns HEPA with Webbing Spacers Carbon Granules © Copyright 2021 Stratasys. All rights reserved. Page 12... - Page 16 _____ c-support@stratasys.com Copyright © 2021 Stratasys Ltd. All rights reserved. DOC-01011 Rev. A THE 3D PRINTING SOLUTIONS COMPANY...