Nortel CallPilot 100 Quick Start Manual
  1. Manuals
  2. Brands
  3. Nortel Manuals
  4. Security System
  5. CallPilot 100
  6. Quick start manual
Nortel CallPilot 100 Quick Start Manual

Nortel CallPilot 100 Quick Start Manual

Nortel networks voicemail messaging call pilot quick start guide
Hide thumbs Also See for CallPilot 100:
Table of Contents

Advertisement

Quick Links

See also: Administration Manual , User Manual
CallPilot 100/150 Quick Start Guide
www.nortelnetworks.com
© November 19, 2004
N0008008 02

Advertisement

Table of Contents
loading

Related Manuals for Nortel CallPilot 100

Summary of Contents for Nortel CallPilot 100

  • Page 1 CallPilot 100/150 Quick Start Guide www.nortelnetworks.com © November 19, 2004 N0008008 02...

  • Page 2: Statement Of Conditions

    In the interest of improving internal design, operational function, and/or reliability, Nortel Networks NA Inc. reserves the right to make changes to the products described in this document without notice. Nortel Networks NA Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

  • Page 3: Callpilot Features

    For information about installing two CallPilot 150 units on one KSU, refer to the CallPilot 100/ 150 Installation and Maintenance Guide.
  • Page 4 Installing the CallPilot 100/150 Installing the CallPilot 100/150 Unpack CallPilot 100/150 Mount the CallPilot 100/150 on the wall Connect the TCM and power cables Initialize CallPilot 100/150 using CallPilot Manager or a telephone CallPilot Manger Can you use the default IP address 192.168.110.10...
  • Page 5 Attach the wall mount bracket to a secure surface by the two inner holes. Use anchors, as necessary. Slip the slot on the back (near the top) of the CallPilot 100/150 onto the bracket. Secure the CallPilot 100/150 using a screw in the lower screw hole.

  • Page 6: Computer Requirements For Callpilot Manager

    To use CallPilot Manager, you must have a network connection to the CallPilot 100/150 or an Ethernet crossover cable. If you do not have a network connection or an Ethernet crossover cable, you can initialize the CallPilot 100/150 using a two-line display telephone.
  • Page 7 If the default IP address is not compatible, you must change the IP address before you connect the CallPilot 100/150 to the network. You can change the IP address using a serial cable or an Ethernet crossover cable (direct PC connection).
  • Page 8 Press the Y key and press the Enter key. The prompt This board’s LAN IP Address (0.0.0.0 = RARP) 10 Type the IP address for the CallPilot 100/150 in a valid dotted format and press the Enter key. The prompt Subnet mask for LAN (0 for none) 11 Type the Subnet Mask for the CallPilot 100/150 in a valid dotted format and press the Enter key.

  • Page 9: Changing The Ip Address Using An Ethernet Crossover Cable

    CallPilot Manager to change the CallPilot 100/150 IP address before you connect it to the network. Note: If you do not have access to the CallPilot 100/150 through the network, you can use an Ethernet crossover cable to configure all of the CallPilot 100/150 parameters.
  • Page 10 If this is a re-install, the Subnet Mask shows the current settings, not the factory default. Primary DNS Enter the IP Address of the Primary DNS server that CallPilot 100/150 uses. If you do not know the IP Address, contact your network administrator.
  • Page 11 From Extension Enter the extension number of the first telephone in a range of telephones you want to create a mailbox for. A mailbox is created for this telephone and for all of the telephones up to the extension number you enter in the To Extension box.
  • Page 12 CallPilot, refer to the CallPilot Manager Set Up and Operation Guide. Note: If you have changed any of the IP addresses or the Subnet Mask, you must reboot the CallPilot 100/150 before you start programming the CallPilot 100/150 parameters. Initializing CallPilot 100/150 using a telephone To initialize CallPilot 100/150 you need to: •...
  • Page 13 Determining CallPilot 100/150 Feature Codes Default Feature Codes are assigned to CallPilot 100/150 by the Norstar system. These default codes are listed in Table 4. When these default Feature Codes are used by other Norstar applications, the Norstar system assigns Feature Codes between 900 and 999 to CallPilot 100/150.
  • Page 14 Initializing CallPilot 100/150 using a telephone Configuring the CallPilot 100/150 initial parameters To configure the CallPilot 100/150 initial parameters: 1. Press ≤·°‹. This is the default System Administration feature code. If your system does not use the default feature codes, enter the System Administration feature code you determined earlier.

  • Page 15: Additional Information

    After you have initialized the CallPilot 100/150, you can begin configuring the CallPilot features. For information about how to configure the CallPilot 100/150, refer to the CallPilot Manager Set Up and Operation Guide or the CallPilot 100/150 Telephone Administration Guide.
  • Page 16 Additional information N0008008 02...

This manual is also suitable for:

Callpilot 150

Table of Contents