Advertisement
Quick Links
PowderHound & Big PowderHound
SKILIFT (2x)
Hex Key with
Bolt (2x)
SkiLift (2x)
Lock Core (2x)
Control Key (1x)
(flat edge)
IMPORTANT WARNING: IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY
ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD
CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS
AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE
PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE
INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO
NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND
ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED
BY A PROFESSIONAL INSTALLER SUCH AS A QUALIFIED GARAGE OR AUTO BODY SHOP.
1033546B-1/18
FreshSesh,
CARRIER (2x)
universal mounting
bracket (4x)
Button Head
Screw (2x)
Locking Keys (2x)
(MOUNTING BRACKET PARTS:)
Hex Wrench (1x)
Base Screw (4x)
Slider Top (4x)
Bail Screw (8x)
installed
Long Bail Screw (8x)
for some
larger factory bars
Upper Bail (4x)
Square Nut (4x)
Pad (4x)
Lower Bail (4x)
Vinyl Pad Sheets (2x)
for factory bars
Part #1033546 Rev.B
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Yakima FreshSesh
Summary of Contents for Yakima FreshSesh
- Page 1 PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER SUCH AS A QUALIFIED GARAGE OR AUTO BODY SHOP.
- Page 2 12” (30cm) and 24” (61cm) SKIS AND BOARDS OVER 170 cm: Crossbar spread must be between 12” (30cm) and 36” (91cm) YAKIMA Q TOWERS: DO NOT REPOSITION YOUR TOWERS! REMOVE BASE SCREW REMOVE ONE BAIL SCREW Use hex wrench. Use hex wrench.
- Page 3 ASSEMBLE ATTACH UPPER BAIL MOVE SLIDING TO SLIDER TOP BAIL TO EXPOSE SCREW HOLES. screw with square nut (inside through hole upper bail.) in pad. engage the screw top onto screw. and nut. yet. CLOSE CARRIER WITH FIRM INSERT SECOND BAIL PRESSURE SCREW THROUGH UPPER BAIL ONLY.
- Page 4 SECURE MOUNTING ASSEMBLY OPEN CARRIER unsecured bail screw. tighten screws. LOAD SKIS OR TIGHTEN CARRIERS TO UNIVERSAL MOUNTS SNOWBOARDS Make sure carriers are vertically universal mount will aligned. sit at an angle. VERIFY BINDING CLEARANCE factory bars are arched and cannot align If you have sufficient with carriers, clearance,...
- Page 5 ATTACH SKILIFT TO ATTACH SKILIFT TIGHTEN FRONT UNIVERSAL MOUNT TO CARRIER BASE SCREWS Tighten any loose bail screws to secure the brackets to the crossbars. mounting brackets for better fit. CLOSE CARRIERS WITH FIRM PRESSURE VERIFY THE CLOSURE! carrier to see if the carrier can open. closing the carrier.
-
Page 6: Weight Limits
Control Key Control Key completely to pull the core out. *SKS refers to the Yakima Same Key System. Refer to your Yakima rack or accessory instructions for Yakima’s Lifetime Warranty. Register online at www.yakima.com for Key Club Membership (to order (located on the set of locking keys) additional matching cores or keys).
Need help?
Do you have a question about the FreshSesh and is the answer not in the manual?
Questions and answers