Table of Contents
Advertisement
Quick Links
XX055-01-00
V1400X-MSSV Multisystem Selector
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements
or that the operation will be entirely error free or perform precisely as described in the documentation. This
system has not been designed to be used in life-critical situations and must not be used for this purpose.
Copyright © 2001 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
NOVA and its logo are trademarks of Vicon Industries Inc.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TELEPHONE: 631-952-CCTV (2288) FACSIMILE: 631-951-CCTV (2288)
24-Hour Technical Support: 800-34-VICON (800-348-4266)
TOLL FREE: 800-645-9116 UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207
Vicon Part No. 8009-8055-01-00 Section 9 Rev 1201
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vicon V1400X-MSSV
Summary of Contents for Vicon V1400X-MSSV
- Page 1 XX055-01-00 V1400X-MSSV Multisystem Selector Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.
-
Page 3: Table Of Contents
Program Message ............................8 CPU................................8 Applications ..............................9 Operation Verification Procedure ......................10 V1300X-DVC/V1300X-RVC Keypads ......................10 V1400X-DVC System Console ........................11 CPU Control System Operation........................12 MAINTENANCE ......................... 13 Contents • • • • i XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... - Page 4 Manual References for Associated Equipment ..................17 CPUs ................................17 Input Devices.............................. 17 TECHNICAL INFORMATION..................... 18 ELECTRICAL............................18 CONTROLS & CONNECTORS......................18 OPERATIONAL ............................19 MECHANICAL ............................19 ENVIRONMENTAL..........................19 Contents • • • • ii XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector...
-
Page 5: Introduction
Selector, multiple CPUs and a Master Input Device and a Monitor. In addition to the Selector, this manual provides abbreviated descriptions of Vicon Input Devices, as the operation of the Selector relies solely on the input device. There are variations in configurations that include the use of a Distribution Control Unit, which are described later. -
Page 6: Installation
Installation Installation of the Selector is simple. This Section will detail complete installation that is comprised of Physical Installation and Cabling sub-sections. Quick Installation Installation • • • • 2 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 7: Unpacking And Inspection
Open the cartons and inspect the equipment for damage. Save the cartons and packing material. If damage is present, contact the carrier and file a damage claim immediately. If the equipment must be returned to Vicon for repair, follow the instructions in the Shipping Information Section of this manual. -
Page 8: Cpu Connection
Figure 5 for the Keypad receptacle. Refer to the Reference Section of this manual for Table 4, Shielded, Dual Twisted-Pair Cable Maximum Operating Distances. Figure 5 Pin Definition for Master Input Device Cable (Keypad) Installation • • • • 4 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 9: Shd Adapter/37-Pin Cable
37-pin side of the SHD Adapter. 8. Connect the other end of the 37-pin cable to the Aux connector (J20) on the Master Keypad. Figure 7 Control In to J20 Cable Assembly Installation • • • • 5 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 10: V1400X-Dvc System Console
NOTE: Refer to the System Console Instruction Manual for information on daisy chaining additional Figure 8 System Console units to the Master System PWR/COMM Pin Definition for Master System Console. Console Cable Installation • • • • 6 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... - Page 11 6. Attach the provided Power Cord to the Rear Panel Power Block. The Selector's Power LED should illuminate indicating it is powered. In addition, the local monitor should display video of the currently selected CPU. Figure 9 Control In to Control Out Cable Installation • • • • 7 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector...
-
Page 12: Operation
Operation The V1400X-MSSV Selector allows one or more Input Devices to control up to 8 different CPU-Based Matrix Systems. Since the Selector does not have any panel controls, a Master Input Device (connected directly to the Selector) is used for operation. Refer to Vicon Instruction Manuals for detailed information on the Keypads and the System Console. -
Page 13: Applications
NOTE: System Console 1 is the Master System Console Selector. NOTE: Keypads and System Consoles Figure 11 can be daisy chained together in the Typical System Setup With V1400X-DVC System Consoles same system. Operation • • • • 9 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 14: Operation Verification Procedure
1. Place the Keypad ON/OFF switch, located on the rear panel, to the ON (I) position. The front panel POWER LED should illuminate. 2. Setup the Master Keypad in accordance with Vicon Instruction Manual X777 using the following parameters: KEYPAD TYPE:... -
Page 15: V1400X-Dvc System Console
Select System Mode Screen Console to operate each CPU with the correct screen functions and protocol. Refer to Figure 13. NOTE: Vicon VPS protocol is equivalent to the NOVA system product line. 4. Go to the 1400 Series Screen for operation. The System prompt should be displayed with the Monitor and Camera prompts. -
Page 16: Cpu Control System Operation
To properly control Cameras and Monitors on various CPUs, it is necessary to setup monitor partitioning and camera seize control on each CPU. Refer to the Instruction Manual for each CPU control system for information on establishing monitor partitioning and camera seize control. Operation • • • • 12 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 17: Maintenance
Maintenance This unit does not require any scheduled maintenance. If a unit does not operate and replacement of the Fuse, as described below does not correct the problem, contact Vicon’s Service Department. Fuse Replacement If a unit is plugged into a known good outlet, switched on, and does not illuminate the Power LED, replace the Fuse. -
Page 18: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 19: Reference
Reference Coaxial Cable CAUTION: Selection of proper cable is essential for the best equipment performance. Vicon assumes no responsibility for poor performance when non-recommended cable types are used. All coaxial cable impedance should be 75 ohms. Materials The preferred cable for video is one with a low DC resistance such as a solid-core bare and pure copper center conductor. -
Page 20: Cable Recommendations
Figure 16. This cable should not exceed 6 ft (15 m). Figure 16 Control In to J20 Cable Pin Definition Reference • • • • 16 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 21: Manual References For Associated Equipment
Microprocessor-Based Control System X553 V1400X V1400 Series NOVA Customer-Programmable System XX009 VPS328/V1422 VPS328/V1422 Digital Control, Installation/Operation X826 Input Devices V1300X-DVC/RVC Intelligent Remote Control Panels X777 V1400X-DVC-G/-3 System Console X923, XX090 Reference • • • • 17 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 22: Technical Information
6-pin removable Terminal Block Connector for each. MON1 - MON8: BNC-F, carrying analog composite video signal. Accessory kit provides 75-ohm terminators to be installed on any unused connectors. Technical Information • • • • 18 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... -
Page 23: Operational
Up to 90% relative, noncondensing. Storage Temperature Range: -40° to 150° F (-40° to 65° C). Storage Humidity Range: Up to 90% relative, noncondensing. Figure 17 Front and Rear Panel Views Technical Information • • • • 19 XX055-01-00 Rev 1201 V1400X-MSSV Multisystem Selector... - Page 24 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Infofax: 800-287-1207 Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom 44/(0) 1489/566300 Fax: 44/(0) 1489/566322 Brussels Office Planet II - Unit E...
Need help?
Do you have a question about the V1400X-MSSV and is the answer not in the manual?
Questions and answers