Related Manuals for Vicon NOVA V1400X-HSB-M
Summary of Contents for Vicon NOVA V1400X-HSB-M
- Page 1 XX018 V1400X-HSB-M Hot Standby Switchover VICON INDUSTRIES INC. 89 ARKAY DRIVE, HAUPPAUGE, NY 11788...
- Page 2 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.
-
Page 4: Fcc Notice
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. -
Page 5: Table Of Contents
Operation .......................... 16 Start-Up Screen............................16 Hot Standby System Controls and Indicators................... 16 Programming ........................18 Maintenance........................18 Powerdown Procedure ..........................18 Fuse Replacement ............................18 Shipping Instructions....................... 19 Index ..........................20 Contents • i XX018 Rev 200 NOVA V1400X-HSB-M... -
Page 6: Important Safeguards
CAUTION damage to the video product. Use only with a mounting RISK OF ELECTRIC SHOCK accessory recommended by Vicon, or sold with the video DO NOT OPEN product. Any mounting of the video product should follow Vicon’s instructions, and a mounting accessory... - Page 7 This prevents damage to the video product due replacement parts specified by Vicon or that have the to lightning and power-line surges. same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other 15.
-
Page 8: Introduction
Monitors Keypads Alarms Receiver 2048 XIA 512 Connections between switchover modules and peripherals. All peripheral equipment, such as switcher card Figure 1 cages, keypads, receivers, Hot Standby System Overview alarm interfaces, etc. Introduction • 1 XX018 Rev 200 NOVA V1400X-HSB-M... -
Page 9: Installation
J11 on the V1400X-SSO-E module* J10 on the V1400X-SSO-E module* J14 on the V1400X-SSO-E module* J13 on the V1400X-SSO-E module* * Systems with more than 1024 receivers only. 2 • Installation XX018 Rev 200 NOVA V1400X-HSB-M... - Page 10 If you have more than 1024 receivers, use Figure 4 to make connections between the V1400X-SSO-E and the CI cards. You may also refer to Table 1. CARD SLOT 3 PRIMARY CPU V1400X-CI-M CARD SLOT 3 SECONDARY CPU V1400X-CI-M Figure 2 Connections between Primary and Secondary V1400X-CI-M Boards Installation • 3 XX018 Rev 200 NOVA V1400X-HSB-M...
- Page 11 CARD SLOT 3 SECONDARY CPU PRIMARY CPU V1400X-CI-M V1400X-CI-M V1400X-SSO J14 J7 (SYSTEM SUPERVISOR CPU) STANDBY PRIMARY Figure 3 Connections between V1400X-CI-M Boards and V1400X-SSO Supervisor Module 4 • Installation XX018 Rev 200 NOVA V1400X-HSB-M...
- Page 12 (SECONDARY SYSTEM SUPERVISOR CPU) STANDBY PRIMARY RECEIVERS / DOMES (1025 ~ 1536) RECEIVERS / DOMES (1537 ~ 2048) Figure 4 Connections between V1400X-SSO-E Supervisor Module (systems with more than 1024 cameras only) Installation • 5 XX018 Rev 200 NOVA V1400X-HSB-M...
-
Page 13: Titler Connections
J2 on Primary V1400X-TC-M cable, pin 2 to pin 2, and so forth. J2 on Secondary V1400X-TC-M TDT cages for outputs 65-128 J3 on Primary V1400X-TC-M J3 on Secondary V1400X-TC-M J7 - J12 unused 6 • Installation XX018 Rev 200 NOVA V1400X-HSB-M... - Page 14 (TIME/DATE/TITLER CPU) STANDBY STANDBY PRIMARY STANDBY Primary TO T/D/T CAGES FOR TO T/D/T CAGES FOR OUTPUTS 01 ~ 64 OUTPUTS 65 ~ 128 Figure 5 Connections between the V1400X-TSO and V1400X-TC-M Boards Installation • 7 XX018 Rev 200 NOVA V1400X-HSB-M...
-
Page 15: Alarm Connections
J10 on Secondary V1400X-AC-M RS-232 alarm port not connected J11 on Primary V1400X-AC-M ground J11 on Secondary V1400X-AC-M not connected RS-232 alarm port not connected J12 on Primary V1400X-AC-M J12 on Secondary V1400X-AC-M 8 • Installation XX018 Rev 200 NOVA V1400X-HSB-M... - Page 16 V1400X-ASO (ALARM CPU) PRIMARY STANDBY PRIMARY STANDBY ALARMS 257 ~ 512 ALARMS 001 ~ 256 RS-232 ALARM RS-232 ALARM INTERFACE PORT INTERFACE PORT Figure 6 Connections between V1400X-ASO Module and V1400X-AC-M Cards Installation • 9 XX018 Rev 200 NOVA V1400X-HSB-M...
-
Page 17: Video Switcher Connections
1-64 J2 on Primary V1400X-VC-M J2 on Secondary V1400X-VC-M video loss detectors and video switcher cages for outputs 65-128 J3 on Primary V1400X-VC-M J3 on Secondary V1400X-VC-M J7 - J12 not used 10 • Installation XX018 Rev 200 NOVA V1400X-HSB-M... - Page 18 The video switcher input to the VLD can be anywhere in the chain but must be on the video bus that controls the VLD’s assigned monitor. You must also configure the high speed switcher in the programming menus correctly and set the alarm assigned to the VLD to NC. Installation • 11 XX018 Rev 200 NOVA V1400X-HSB-M...
-
Page 19: Supervisor Connections
J8 on V1400X-SSO module J7 on V1400X-SSO module J11 on V1400X-SSO module J10 on V1400X-SSO module J14 on V1400X-SSO module J13 on V1400X-SSO module J17 on V1400X-SSO module J16 on V1400X-SSO module 12 • Installation XX018 Rev 200 NOVA V1400X-HSB-M... - Page 20 STANDBY PRIMARY RS-232 HOST COMPUTER PORT RECEIVERS / DOMES (0513 ~ 1024) STATUS DISPLAY MONITOR RECEIVERS / DOMES (0001 ~ 0512) KEYPADS Figure 8 Connections between the V1400X-SSO Modules and V1400X-SV-M Cards Installation • 13 XX018 Rev 200 NOVA V1400X-HSB-M...
- Page 21 Note: On the RS-232 receiver and keypad connectors, pin 1 is located on the upper right as you view the unit from the rear. Table 8 Connections for Host Computer Pin Number Function Pin Number Function not used not used ground not used not used – 14 • Installation XX018 Rev 200 NOVA V1400X-HSB-M...
-
Page 22: Control Connections Between Switchover Modules
The screw terminal strip on the V1400X-SSO module (and V1400X-SSO-E module, if applicable to your system) has two positions, while the other modules each have three. V1400X-SSO V1400X-VSO V1400X-ASO V1400X-TSO V1400X-SSO-E Figure 9 Control Connections Installation • 15 XX018 Rev 200 NOVA V1400X-HSB-M... -
Page 23: Operation
Refer to Figure 10 and to the front panel of the V1400X-SSO supervisor switchover module for control switches and LEDs. 1. AUTO/PRI/SEC: Three-position switch offers manual selection of the Primary CPU (PRI), Secondary (SEC) CPU, and automatic (AUTO) operation. 16 • Operation XX018 Rev 200 NOVA V1400X-HSB-M... - Page 24 Flashes when data is being transferred from the Primary to Secondary systems. 6. POWER: Illuminates when the V1400X-SSO module is powered. AUTO OFF–ON PRIMARY STANDBY PRIMARY STANDBY PRIMARY STANDBY DOWNLOAD POWER ALARM STATUS CONTROL DATA V1300X–SSO Figure 10 V1400X-SSO Supervisor Front Panel Operation • 17 XX018 Rev 200 NOVA V1400X-HSB-M...
-
Page 25: Programming
3. Replace the plastic cover on the fuse, replace the cover of the module, and replace the unit in the rack. 4. Reconnect the power cord and confirm that there is power to the unit. 18 • Programming XX018 Rev 200 NOVA V1400X-HSB-M... -
Page 26: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 27: Index
Support 19 Telephone Numbers 19 Titler 6 V1400-ASO 8 V1400X-AC-M 8 V1400X-CI-M 2 V1400X-SSO 3, 12, 16 V1400X-SSO-E 3 V1400X-SV-M 12 V1400X-TC-M 6 V1400X-TSO 6 V1400X-VC-M 10 V1400X-VSO 10 Video Switcher 10 20 • Index XX018 Rev 200 NOVA V1400X-HSB-M... - Page 28 Vicon Industries Inc. Offices U.S. Offices Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Infofax: 800-287-1207 Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom 44/(0) 1489/566300 Fax: 44/(0) 1489/566322 Brussels Office...
Need help?
Do you have a question about the NOVA V1400X-HSB-M and is the answer not in the manual?
Questions and answers