Technical Data; Installation - Scheppach ASP50-ES Original Instruction Manual

• Switch the appliance off after every use and prior to
every cleaning/maintenance procedure.
• Risk of fire. Do not vacuum up any burning or glow-
ing objects.
• The appliance may not be used in areas where a
risk of explosion is present.
• Immediately switch the appliance off or pull the pow-
er plug if foam forms or liquids escape!
• Do not use abrasives, glass or universal cleaners!
Never immerse the appliance in water.
Certain materials may produce explosive vapours or
mixtures when agitated by the suction air! Never vac-
uum up the following materials:
• Explosive or combustible gases, liquids and dust
particles (reactive dust particles)
• Reactive metal dust particles (such as aluminium,
magnesium, zinc) in combination with highly alka-
line or acidic detergents
• Undiluted, strong acids and alkalies
• Organic solvents (such as petrol, paint thinners, ac-
etone, heating oil).
In addition, these substances may cause the appliance
materials to corrode.
m WARNING!
This electric tool generates an electromagnetic field
during operation. This field can impair active or pas-
sive medical implants under certain conditions. In or-
der to prevent the risk of serious or deadly injuries,
we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.

6. Technical Data

Mains voltage
Power
Maximum device socket
power
Total power
Water tank capacity
Suction performance
Protection category
Protection class
220-240 V~ 50/60 Hz
1400 W
2000 W
3400 W
50 L
19Kpa
IPX4
I
www.scheppach.com
7.

Installation

m IMPORTANT!
Prior to use, ensure that the device has been correct-
ly and fully assembled.
Unpacking (fig. 1, 2, 3)
• Release the locking hooks (5) and remove the ma-
chine head (2). The accessories are located inside
the stainless steel container (15). Only the metal
extension tube (27) is located outside the stainless
steel container (9) in the packaging. Remove all of
the accessories from the stainless steel container
(15).
Fitting the wheels with axle (9) and the castors (12)
(fig. 4, 5).
• Place the wheels with axle (9) into the recesses
provided on the wheel mounting base (10). Fasten
the wheels with axle (9) with the screws for the ax-
le-mounted wheels (29) with the help of a screwdriv-
er (not included in the delivery).
• Press the two castors (12) into the holes in the wheel
mounting base (10).
Installing the push grip (4) (fig. 6)
• Push the push grip (4) into the push grip mount (6) on
the stainless steel container. In doing so, ensure that
the push grip (4) latches into place.
Installing the machine head (2) and the handle (1)
(fig. 7)
• Place the machine head (2) on the stainless steel
container (15). Secure the machine head (2) with the
locking hooks (5). When installing the machine head
(2), ensure that the locking hooks (5) latch into place
correctly.
• Place the handle (1) on the machine head (2) and
fasten it with two screws (28) with a screwdriver (not
included in the delivery).
Installing the drain hose (11) (fig. 8, 9, 10)
• Thread the retaining clip (13) over the drain hose
(11). (Fig. 8)
• Fit the drain hose (11) to the drain hose connection
(14). Position the retaining clip (13) such that it fas-
tens the drain hose (11) to the drain hose connection
(14). Tighten the retaining clip (13) with a screwdriver
(not included in the delivery). (Fig. 9)
GB | 21