Subscribe to Our Youtube Channel
Related Manuals for Woxcon SCU41T-TB
Summary of Contents for Woxcon SCU41T-TB
- Page 1 User Manual SCU41T-TB 4x1 Conference Tabletop Box with Soft Codec All Rights Reserved Version: SCU41T-TB_2020V1.0...
-
Page 2: Table Of Contents
4x1 Conference Tabletop Box with Soft Codec Table of Contents 1. Product Introduction ..........................1 1.1 Features ............................1 1.2 Package List ..........................2 2. Specification ............................3 3. Panel Description ............................ 4 4. System Connection ..........................5 5. Panel Button Control ..........................6 5.1 Signal Switching ........................... -
Page 3: Product Introduction
24V PoC, allowing the compatible receiver (e.g. SCU42T- CODEC-R, sold separately) to draw power from the tabletop box over the CATx cable. The SCU41T-TB also supports front panel button control, Web GUI, CEC and RS232 control. 1.1 Features 4x1 switcher with three HDMI inputs and one USB Type-C input. -
Page 4: Package List
4x1 Conference Tabletop Box with Soft Codec 1.2 Package List 1x SCU41T-TB Conference Tabletop Box Transmitter 2x Mounting Screws (Ф10*15*M3) 2x Mounting Screws (6.8*12-M5*8) 2x Wing Mounting Screws 1x RS232 Cable 1x AC Power Cord 1x User Manual Note: Please contact your distributor immediately if any damage or defect in the... -
Page 5: Specification
4x1 Conference Tabletop Box with Soft Codec 2. Specification Input & Output Video Input (3) HDMI, (1) USB-C Video Input Connector (3) Type-A female HDMI, (1) USB 3.0 Type-C HDMI Input Resolution Up to 4K@60Hz 4:4:4 8bit, HDR 10, HDR 10+, Dolby Vision. USB-C Input Resolution Up to 4K@60Hz 4:4:4 Video Output... -
Page 6: Panel Description
4x1 Conference Tabletop Box with Soft Codec 3. Panel Description AC100V-240V HDMI 1 HDMI 2 USB-C HDMI 3 RX HDMI INPUT Tx Rx FIRMWARE HDMI IN 1 HDMI IN 2 USB-C IN HDMI OUT HDMI IN 3 RS232 ETHERNET DEVICE CHARGING TCP/IP DEVICE... -
Page 7: System Connection
4x1 Conference Tabletop Box with Soft Codec ⑪ PC/HOST 1&2: Two USB Type-B ports for HOST PCs connection. The HOST PC can be controlled by the USB devices (e.g. mouse, keyboard, etc.) which are connected to USB Type-A ports (DEVICE). ⑫... -
Page 8: Panel Button Control
4x1 Conference Tabletop Box with Soft Codec 5. Panel Button Control 5.1 Signal Switching Press INPUT button to manually select input source, the corresponding LED of HDMI 1, HDMI 2, USB-C, HDMI 3 or RX HDMI will illuminate green. When the LED of RX HDMI turns green, the RX HDMI source is switched to the HDMI output port of the receiver, and the source input of tabletop box is switched to HDMI 3 input, then the LED of HDMI 3 also lights green. -
Page 9: Gui Control
4x1 Conference Tabletop Box with Soft Codec 6. GUI Control The unit can be controlled via TCP/IP. The default IP settings are: IP Address: 192.168.0.178 Subnet Mask: 255.255.255.0 Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage: Username: admin Password: admin Type the user name and password, and then click Login to enter the section for video... -
Page 10: Control Tab
4x1 Conference Tabletop Box with Soft Codec 6.1 Control Tab 6.1.1 Signal Switching Video: Click button “HDMI 1”, “HDMI 2”, “USB-C”, “HDMI 3” or “RX HDMI” to select the corresponding input source. Auto Switching: ü Select 5V or TMDS signal detection mode. ü... -
Page 11: Display Control
4x1 Conference Tabletop Box with Soft Codec 6.1.2 Display Control Auto Display Control: Enable or disable the auto display control mode. In auto display control mode, the unit will automatically perform the following operations. ü System On: When the unit detects source signal input (5V or TMDS), or receives “Wake Up” command, it will automatically perform the following operation steps: Send “Display On”... -
Page 12: Device Control
4x1 Conference Tabletop Box with Soft Codec Note: The “Display On”, “Display Off” and “Display Input Select” RS232 commands; the Delay Time, No Signal Timeout and No Activity Timeout can be set by GUI Display Setting tab or RS232 command. For more details, please refer to 6.2 Display Setting Tab or 7.4 Display Setting. -
Page 13: Display Setting Tab
4x1 Conference Tabletop Box with Soft Codec ü Passive: Automatically follows the input source’s HDCP content. ü Active: Automatically output HDCP 1.4 content, and if the input source has no HDCP content, the output also has no HDCP content. 6.2 Display Setting Tab Baud Rate: Set the baud rate for display device. -
Page 14: Edid Tab
4x1 Conference Tabletop Box with Soft Codec Input Delay: Set the sending interval time between the “Display On” and “Display Input Select” commands. Display Input Select: Enter the “Display Input Select” RS232 command to be saved, and then click “Save”. The command is usually used to select input source for the display device. -
Page 15: Usb Host Tab
4x1 Conference Tabletop Box with Soft Codec 6.4 USB Host Tab The system provides USB HOST PC 1, PC 2 or USB-C to be selected, and it provides USB Type-A ports for connecting USB devices (e.g. mouse, keyboard, etc.) used to control the selected USB HOST. - Page 16 4x1 Conference Tabletop Box with Soft Codec...
-
Page 17: Tags Tab
4x1 Conference Tabletop Box with Soft Codec 6.5 Tags Tab Modify the input source tags. 6.6 Network Tab Set Static IP or Dynamic Host Configuration Protocol (DHCP). Modify the static IP Address, Subnet Mask, and Gateway. -
Page 18: Password Tab
4x1 Conference Tabletop Box with Soft Codec 6.7 Password Tab Reset the login username and password. 6.8 GUI Upgrade Please visit at http://192.168.0.178:100 for GUI online upgrade. Type the username and password (the same as the GUI log-in setting, modified password will be available only after rebooting) to login the configuration interface. - Page 19 4x1 Conference Tabletop Box with Soft Codec...
-
Page 20: Rs232 Control
4x1 Conference Tabletop Box with Soft Codec 7. RS232 Control The unit provides RS232 port for control device (e.g. PC) connection. After setting all needed input and output devices according to the system connection diagram, please install the RS232 control software (e.g. docklight) into the control PC to send RS232 command. - Page 21 4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Get the device standby or working #GET_POWER @POWER 0 status. Set GUI IP address. #SET_GUI_IP_ADDR #SET_GUI_IP_ADDR param1 = 0~255 192.168.0.179 param1.param2.param3.para param2 = 0~255 param3 = 0~255 @SET_IP 192.168.0.179 param4 = 0~255 #GET_GUI_IP_ADDR...
-
Page 22: Signal Switching
4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Turn on/off TX and RX cascade #SET_INT_CASCADE ON connection. #SET_INT_CASCADE param1 = ON, OFF. #SET_INT_CASCADE ON - Turn on TX and RX param1 cascade connection. @INTER_CASCADE ON OFF - Turn off TX and RX @INTER_CASCADE OFF cascade connection. -
Page 23: Display Control
4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback 1 - Enable #GET_AUTO_SWITCH Get the source switching mode. @AUTO_SWITCH 0 7.3 Display Control Command Example and Command Function Feedback Enable the auto display control @OPEN CEC DISPLAY #AUTO_CEC_SET_PANEL_O mode. -
Page 24: Display Setting
4x1 Conference Tabletop Box with Soft Codec 7.4 Display Setting Command Example and Command Function Feedback Set the “Display On” command “xxxx” to be saved. When pressing #SET_ON_A_1:ABCDEFG the “DISPLAY ON” button on front #SET_ON_H_1:11 22 33 panel, the command will be automatically sent to the display device. - Page 25 4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Set the “Display Input Select” #SET_DIS_SEL_A_1:ABC command “xxxx” to be saved. The DEFG command is usually used to select #SET_DIS_SEL_H_1:11 input source for display device. 12 13 param1 = A, H #SET_DIS_SEL_param1_par §...
-
Page 26: Edid Setting
4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback Get the No Activity Timeout. The @DELAY TIME TO %d display device will be automatically MINUTES, TO TURN OFF #GET_NO_ACT_TIME shut down when no any activity is DISPLAY WHEN NO detected within the setup time. - Page 27 4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback § Null - All source input devices. param2 = 0~16 EDID Bypass (HDBT OUT) EDID Bypass (HDMI OUT) 1280x720@60Hz Stereo Audio 1920x1080@60Hz 8bit Stereo Audio 1920x1080@60Hz 8bit High Definition Audio 1920x1080@60Hz 3D Stereo Audio...
-
Page 28: Usb Control
4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback #UPLOAD_USER_EDID 1 #UPLOAD_USER_EDID 2 Upload the user-defined EDID. @USER_EDID_READY 1 #UPLOAD_USER_EDID param1 = 1, 2 USER EDID 1 UPLOAD param1 1 - Upload the user-defined EDID 1. 2 - Upload the user-defined EDID 2. -
Page 29: Relay Control
4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback § NA - NO Operation Get the mapping relationship when #GET_USB_MAP the USB HOST follows the input #GET_USB_MAP H1 #GET_USB_MAP H2 video source switching. param1 = H1, H2, H3, Null #GET_USB_MAP param1 §... -
Page 30: Firmware Upgrade
4x1 Conference Tabletop Box with Soft Codec Command Example and Command Function Feedback @RELAY2_AUTO_TIME 10 SECONDS 8. Firmware Upgrade Please follow the steps as below to upgrade firmware of the tabletop box by the FIRMWARE port on the rear panel: 1) Prepare the latest upgrade file (.bin) and rename it as “FW_MERG.bin”.
Need help?
Do you have a question about the SCU41T-TB and is the answer not in the manual?
Questions and answers