Table of Contents
Related Manuals for Imesa T Series
Summary of Contents for Imesa T Series
- Page 1 E150401X_ENG 27/07/2015 SERVICE BOOK “IM7” FOR TUMBLE DRYERS “T” MODEL SINCE SERIAL NUMBER: E201003027 WITH IM7 SOFTWARE rel. 2.20 OR HIGHER IMESA S.p.A. Via degli Olmi 22 31040 Cessalto (TV), Italia tel. +39.0421.468011 fax +39.0421.468000 www.imesa.it...
-
Page 2: Table Of Contents
E150401X_ENG 27/07/2015 INDEX SECTION “A” – INTRODUCTION ..................4 CONTENTS OF THE MANUAL ................. 4 SAFETY RULES ......................4 MANUFACTURER LIABILITY ..................5 IM7 MICROPROCESSOR DESCRIPTION ..............6 SECTION “B” – ALARMS AND TROUBLESHOOTING ............7 SECTION “C” – USER’S MENU PARAMETERS ..............7 ENTERING THE USER’S MENU ................ - Page 3 E150401X_ENG 27/07/15 USER PASSWORD MODIFICATION ..............19 TEC. PASSWORD MODIFICATION ................ 20 PARTIAL POWER ....................20 COIN BOX ....................... 21 DEVICE TEST ......................22 LOADING TEST ....................... 23 ASSISTANCE PHONE..................... 23 P.I.D......................... 24 ENERGY MENU ...................... 24 INITIAL COOLING ....................24 STEAM CONFIGURATION ..................
-
Page 4: Section "A" - Introduction
1) CONTENTS OF THE MANUAL This manual includes all the information to make a correct service on programmers installed on IMESA’s dryers series "T". This document is written in compliance with the European rules in force. Information are addressed to the service technician, who must be sure to completely understand them before to work on the machine. -
Page 5: Manufacturer Liability
E150401X_ENG 27/07/15 otherwise the warranty condition will immediately expire. ATTENTION! Even if the main switch is in position “0”, main cables before it are under tension! OPERATOR’S PSYCHO-PHYSICAL CONDITION User of the tumble dryer must be in perfect psychophysical condition. While working assume a vertical position in front of the machine. -
Page 6: Im7 Microprocessor Description
E150401X_ENG 27/07/15 4) IM7 MICROPROCESSOR DESCRIPTION Entry into service: April 2010. Installed on: Driers "T" series Data interface: NO SW upgradeable: NO Programmable: YES Inverter communication: ANALOG and STEP Keyboard: MEMBRANE + DISPLAY Door lock: NO Coin-op release: YES Power board: NO... -
Page 7: Section "B" - Alarms And Troubleshooting
E150401X_ENG 27/07/15 SECTION “B” – ALARMS AND TROUBLESHOOTING It’s possible to see alarms and troubleshooting directly from www.imesa.it. Click the link below to login to the site and download technical manuals. SECTION “C” – USER’S MENU PARAMETERS 1) ENTERING THE USER’S MENU It’s possible to complete the programming by changing the parameters of the user’s area. - Page 8 E150401X_ENG 27/07/15...
-
Page 9: Parameters
E150401X_ENG 27/07/15 2) PARAMETERS 1. PROGRAMS The following list menu shows the 30 standard programs available in the memory of IM7 control card unit. The programs can be modified: The adjustable parameters are: o PROGRAM NAME: Change the name of the program through the use of alphanumeric characters. - Page 10 E150401X_ENG 27/07/15 step can works with a different temperature than the others. During the program composed with multiple step it’s possible to activate the “skip” function if the parameter “FEED CONTROL” is enabled (this parameter is present only in the technical menu). o STEP1-STEP2...STEPx: (It appears only if "TIME"...
-
Page 11: Language
E150401X_ENG 27/07/15 Default = 35 RPM. “FAN INVERTER” is set to “YES” in the technical o FAN SPEED: (It appears only if menu). It allows to select the fan speed for a given program. The speed will still be editable, even if in a non-definitive way, during the working process of the machine. Default = 2 o PARTIAL POWER: (it appears only if the parameter PARTIAL POWER... -
Page 12: Section "D" - Technical Parameter Menu
E150401X_ENG 27/07/15 SECTION “D” – TECHNICAL PARAMETER MENU 1) ACCESS TO TECHNICAL MENU It’s possible to complete the programming by changing the parameters of the technical area. Access is as follows: To access do as follows: STANDARD IM7 CONTROL CARD with IM7 STANDARD KEYBOARD: o Turn on the machine;... -
Page 13: Parameters
E150401X_ENG 27/07/15 2) PARAMETERS 1. TEMPERATURE UNIT MEASURE: It allows to select the temperature’s unit of measurement. The options are °C (Celsius) or °F (Fahrenheit). Default = °C. Below is a table comparing the two temperature scales. °C °F 32.0 50.0 59.0 68.0 77.0 86.0 95.0 104.0 113.0 122.0 131.0 140.0 149.0 158.0 167.0 176.0 185.0 194.0 2. -
Page 14: Working Hours Machine
E150401X_ENG 27/07/15 If there is any drying programs with higher temperature than the maximum, automatically will be lowered until the set value. 4. WORKING HOURS MACHINE Vengono trascritte le ore ed i minuti di effettivo lavoro. 5. TOTAL CYCLE N° (ABSOLUT) Sono riportati i cicli eseguiti dalla prima accensione delle macchina. -
Page 15: Reversing Drum
E150401X_ENG 27/07/15 Only on standard machines it is possible to vary the speed of the drum while the drying program is running. By clicking the "ENTER" button, select with the cursor the symbol for the speed and change it with the "▲" and "▼". If the parameter is accidentally set to "YES"... -
Page 16: Drum Max Rpm
E150401X_ENG 27/07/15 reversing system. 14. DRUM MAX RPM It defines the maximum limit of the drum speed where the machine is equipped with inverter (variable frequency drive) on the drum’s motor. Default = 80 RPM. Minimum = 0 RPM. Maximum = 100 RPM. This parameter only appears when the “DRUM INVERTER”... - Page 17 E150401X_ENG 27/07/15 BLOWER’s SPEED FREQUENCY 25 Hz 30 Hz 40 Hz 50 Hz The feature is not available for machine equipped by gas heating. electrical system drive following integration: The inverter is installed in the rear of the machine, externally with respect to the housing of the contactors.
-
Page 18: Wrinkle
E150401X_ENG 27/07/15 16. NO WRINKLE The anti wrinkle function allows to keep the drum rotating after the end of the drying cycle with the fan off. The laundry is kept in motion to avoid the formation of permanent creases that normally are created if it garments stay for a long time inside the drum. Default = NO (not activated). -
Page 19: Max Time Drying
E150401X_ENG 27/07/15 While the no wrinkle cycle is working, the display shows the following screens: The no wrinkle cycle can be interrupted by opening the door when or otherwise by pressing the stop button. 17. MAX TIME DRYING The parameter defines the maximum time duration of drying program. Default = 99’. -
Page 20: Tec. Password Modification
If the password of the technical area was lost, you will need to put send back the IM7 control card unit to IMESA SPA for the full reset (including further custom programs). 21. PARTIAL POWER For machines equipped with electric heating it is possible to choke the installed power. -
Page 21: Coin Box
E150401X_ENG 27/07/15 22. COIN BOX If set to “YES” the aspect and the behavior of the IM7 control card unit become for coin-op use. The “COIN BOX MENU” become present inside the user’s menu (6 times “START” button). The drying programs will not start if the desired cost is not reached in the program. -
Page 22: Device Test
E150401X_ENG 27/07/15 Default = NO. The activation of this menu makes it difficult to navigate with a standard keyboard. The correspondence of keys becomes the following: CORRESPONDENCE BETWEEN STANDARD KEYBOARD AND COIN-OP KEYBOARD COIN-OP (SELF SERVICE) COIN-OP (SELF SERVICE) HIGH HIGH MEDIUM MEDIUM... -
Page 23: Loading Test
E150401X_ENG 27/07/15 RESET GAS RELAY RESET SIGNAL TO THE GAS IGNITION DEVICE** BUZZER BUZZER * Only for steam heated machine. ** This chanel is not working with gas valve code: 3970VA840016 WARNING! The devices "HEATING RELAY 1" and "HEATING RELAY 2" correspond to the activation of the heating. -
Page 24: Energy Menu
E150401X_ENG 27/07/15 maintenance prompt (see section RESET MAINTENANCE WARNING). The phone number can be dialed only numeric characters and may coincide with the phone number of the dealer or technician. Default = not set. 26. P.I.D. Not enabled. 27. ENERGY MENU This menu allows you to set the units measurement and the values for the calculation of energy consumed by the tumble dryer. -
Page 25: Tandem Configuration
THE LAUNDRY ROOM For more information and troubleshooting about these specific alarms, see the document E140304X available on www.imesa.it. 30. TANDEM CONFIGURATION Not enabled 31. SEGNALAZIONE PRESSOSTATO ARIA With reference to the control of the air pressure switch in the section “STEAM... - Page 26 E150401X_ENG 27/07/15 be managed automatically depending by the residual moisture to be obtained at the end of cycle. The function is possible on all dryers with IM7 with software version equal and higher than 2.11. It can be activated on all 30 programs in memory by changing the parameter "PROGRAM TYPE"...
-
Page 27: Gestione Allarme Termiche
E150401X_ENG 27/07/15 Example with DRY moisture level: N° INTERVENTIONS = 1 HYSTERESIS = 5°C COOLDOWN DELAY = 10’ Example with EXTRA DRY moisture level: o N° INTERVENTIONS = 3 o HYSTERESIS = 5°C o COOLDOWN DELAY = 0’ 34. GESTIONE ALLARME TERMICHE Since serial number E201003027 up to serial E201310100 it was used exclusively the contact N.C. - Page 28 E150401X_ENG 27/07/15 It will appear the screen for the password entry. Type 4 times the “START/PAUSE” button and 2 times “▲“ (on standard machine) or type 4 times “START” and 2 times “HIGH” (on coin-op machines). Search for parameter “GESTIONE ALLARME TERMICHE” and set N.C. on machine produced before the serial number E201310101, for later serial number set N.O.
Need help?
Do you have a question about the T Series and is the answer not in the manual?
Questions and answers