Adjust The Output Level From The Speakers (Gain Setting); Listening To Higher Quality Cd Sound (Cd Digital Direct) - Marantz DV-12S1 User Manual

Marantz user guide dvd player dv-12s1
Hide thumbs Also See for DV-12S1:
Table of Contents

Advertisement

Adjust the output level from
the speakers (Gain setting)
This setting should be made when the AUDIO OUT
(5.1 channel) jacks on the rear panel are connected to
an AV amplifier or receiver. The output level of each
speaker in your system can be set and confirmed. The
factory setting is set to [Fix]. However, when you want
to adjust the output level, select [Variable].
Audio1
Audio2
Video
Language
Audio DRC – Off
Audio Out –
Speaker Setting
Gain Setting
CD Digital Direct – Off
Move
Settings: Fix*
Variable
When "Variable" is selected
1
Move the cursor control joystic up or down to
select the speaker.
Speakers set to [Off] in the [Speaker Setting] setting
cannot be selected.
Audio1
Audio2
Video
Language
Gain Setting
L
0.0 dB
–2.0 dB
C
R
0.0 dB
RS
0.0 dB
0.0 dB
LS
SW
0.0 dB
Select
Move
ENTER
2
Move the cursor control joystick right or left to
set the output level.
The value can be adjusted in the range of -6.0 dB to 6.0
dB in 0.5 dB increments. The output level of front L/R
speakers are fixed and therefore cannot be adjusted.
3
Repeat steps 1 and 2 for each speaker in your
system.
Set to Test tone
You can't use the Test Tone function when the [Audio
Out] setting is [2 Channel] (page 33).
The Test Tone will not work with the disc tray open, or
while a disc is playing.
4
Move the cursor control joystic up to select
[Gain Setting] and press cursor control joystic
right.
5
Move the cursor control joystic up or down to
select the speaker.
Off:
Test tone is not output. (Factory Setting)
On:
Test tone output is manually controlled.
Auto: Test tone is automatically output.
Audio1
Audio2
Video
Language
Test Tone
L
On
Off
C
R
Off
Off
RS
LS
Off
SW
Off
Move
ENTER
General
5.1 Channel
Fix
Variable
SETUP
Exit
*
Factory setting
General
L
R
SW
LS RS
Return
Exit
SETUP
General
L
R
SW
LS RS
Return
Select
Exit
SETUP
When "On" is selected
Move the cursor control joystick up to the speaker
selection line, then Move the cursor control joystick right
or left to select the speaker to output the test tone from.
The test tone is output from the selected speaker. To
output the test tone from another speaker, change the
speaker selection.
When "Auto" is selected
Test tone is output in the following order.
(Front) Left, Center, (Front) Right, Surround Right,
Surround Left, (Front) Left, ...
6
Move the cursor control joystic up to select
[Test Tone] and press cursor control joystic
left.
This takes you back to the Gain Setting screen.
7
Move the cursor control joystick up or down to
select the speaker, then move the cursor
control joystick right or left to adjust the output
level while listening to the test tone.
To stop the test tone
Move the cursor control joystick down to the "Test Tone"
setting, then move the cursor control joystick right or left to
select [Off] in the [Test Tone] setting.
Notes
• When [Variable] is selected, the output level of all speakers is
uniformly set to –6.0 dB. The output level of each speaker
(center, surround, or sub woofer) can then be adjusted in the
range of –6.0 dB to 6.0 dB. "6.0 dB" is the maximum level of
[Variable] and also the level set for [Fix]. Therefore, when
[Variable] is selected, the output level will usually be lower than
when the setting is set to [Fix].
• The [Variable] setting has no effect on CD and Video CD
playback.
• The test tone is not output when the setting is set to [2 Channel]
in the [Audio Output] setting (page 33), while the disc tray
opens, or while a disc is playing.
Listening to higher quality CD
sound (CD Digital Direct)
By setting the [CD Digital Direct] setting to [On], internal
By setting the [CD Digital Direct] setting to [On], internal
circuitry unrelated to CD playback can be bypassed to
circuitry unrelated to CD playback can be bypassed to
produce a higher quality CD sound.
produce a higher quality CD sound.
Audio1
Audio1
Audio2
Audio2
Video
Video
Language
Language
Audio DRC – Off
Audio DRC – Off
Audio Out –
Audio Out –
2 channel
2 channel
Speaker Setting
Speaker Setting
Gain Setting
Gain Setting
Fix
Fix
CD Digital Direct
CD Digital Direct
On
On
Off
Off
Move
Move
Settings: On (Bypass unnecessary circuitry for CD
Settings: On (Bypass unnecessary circuitry for CD
playback.)
playback.)
Off* (Passes through the necessary circuitry for
Off (Passes through the necessary circuitry for
DTS CD playback.)
DTS CD playback.)
Note
Note
If this setting is set to [On] when a DTS CD is played back, noise is
If this setting is set to [On] when a DTS CD is played back, noise is
produced.
produced.
ENGLISH
General
General
SETUP
SETUP
Exit
Exit
*
*
Factory setting
Factory setting
35

Advertisement

Table of Contents
loading

Table of Contents