Table of Contents
Advertisement
Quick Links
LAUNCH
X-PROG3
Copyright
Copyright © 2020 by LAUNCH TECH CO., LTD. All rights reserved. No part of
this publication may be reproduced, stored, or transmitted in any form without
the written permission of the copyright owner.
Trademark
Launch is a registered trademark of LAUNCH TECH CO., LTD in China and
other countries. All other marks are trademarks or registered trademarks of
their respective owners.
Disclaimer
The contents of this document are subject to changes without notice due to
continued improvements in design, manufacture, and methodologies. Launch
is not liable for the damage or losses due to the use of this document.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
a. This device may not cause harmful interference
b. This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
I
www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu
Advertisement
Table of Contents
Summary of Contents for LAUNCH TECH X-PROG3
- Page 1 LAUNCH X-PROG3 Copyright Copyright © 2020 by LAUNCH TECH CO., LTD. All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form without the written permission of the copyright owner. Trademark Launch is a registered trademark of LAUNCH TECH CO., LTD in China and other countries.
- Page 2 LAUNCH X-PROG3 -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Important: Please read this manual carefully and understand the safety precautions before performing any operation to this product.
- Page 3 LAUNCH X-PROG3 replaced with an incorrect type. • Do not disconnect power abruptly when the test equipment is being formatted or in process of uploading or downloading. Or else it may result in program error. • Do not delete unknown files or change the name of files or directories that were not created by you, otherwise the test equipment software might fail to work.
-
Page 4: Table Of Contents
1 About this Manual ................... 1 1.1 Target Reader ..................1 1.2 Typographic Conventions ..............1 1.3 Symbols ....................1 2 About X-PROG3 ....................2 2.1 Product Overview ................2 2.2 Power Source ..................3 2.3 Technical specifications ............... 4 3 Diagnostics ..................... -
Page 5: About This Manual
1 About this Manual This manual introduces the basic information of X-PROG3 and instruction on the product usage. X-PROG3, the next generation of X-PROG1, is a powerful anti-theft solution and an ideal choice for professional repair shops and vehicle maintenance businesses. It has achieved vehicle key, Engine and gear box programming, featuring powerful multiple parts reprogramming and wide range of vehicle coverage. -
Page 6: About X-Prog3
LAUNCH X-PROG3 2 About X-PROG3 2.1 Product Overview www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu... -
Page 7: Power Source
LAUNCH X-PROG3 Part Name Description To connect with all anti-theft DB26 diagnostic connector cables. Benz key slot To place Benz car key. To place car key for RF Key slot defection. Key chip slot To place key chip. • Red light indicates faults. -
Page 8: Technical Specifications
39 x 107 x 298 mm 3 Diagnostics X-PROG3 diagnostic function supports key programming, engine and gearbox replacement for various of vehicles, you can retrieve ECU information, read, erase, and write in for a range of chips as shown in the product options. -
Page 9: Establish Wireless Connection
VCI connector using a USB cable for effective data transmission. 1. Slide down the status bar from the top. 2. Touch , go to Wireless and network->Bluetooth. 3. Select the X-PROG3 to be connected, wait until the connection is successful. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu... -
Page 10: Perform Common Operations
LAUNCH X-PROG3 • 3.1.3 Perform Common Operations You should enter the function interface before using the programmer. Turn on a Launch diagnostic tool, and/or open on the home screen. On the main diagnostic screen, enter Anti-theft system either from Local Diagnose or Reset, touch OK. -
Page 11: Diagnostic Operations
LAUNCH X-PROG3 3.2 Diagnostic Operations 3.2.1 Key Programming You can use anti-theft system to access key chip programming functions. The product supports reading, retrieving and writing key information, as well as other key-related functions. • Connecting diagnostic system Note: The USB cable shown in below diagram is not included in the packing list for now, using a USB cable could effectively enhance your data transmission speed. - Page 12 LAUNCH X-PROG3 b. Touch OK to confirm the IMMO Type. c. Touch Key Operation. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 13 LAUNCH X-PROG3 d. Touch Key Learning. e. Touch OK after reading the the onscreen instruction. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 14 LAUNCH X-PROG3 f. Touch OK. g. Touch OK to save the key data. h. Enter the key file name and touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 15 LAUNCH X-PROG3 i. Key file saved, touch OK to confirm. 2. Generate a new key. a. Touch the desired blank key position. b. Place the new key into the programmer key slot and touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
-
Page 16: Gear Box Programming
LAUNCH X-PROG3 c. Confirm the key type, if the you are using a smart key, touch YES. d. If the key generation is done, touch OK to confirm. • 3.2.2 Gear Box Programming You can use gear box programming function to restore the old gear box data or write in new data after a new gear box is replaced. - Page 17 LAUNCH X-PROG3 Note: • The USB cable shown in below diagram is not included in the packing list for now, using a USB cable could effectively enhance your data transmission speed. • Certain Vehicle gear boxes are connected based on the real chassis type, for information how to connect the gear box, refer to the onscreen connection diagram.
- Page 18 LAUNCH X-PROG3 b. Touch the correct chassis type. c. You will then see a corresponding connection diagram. Touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 19 LAUNCH X-PROG3 2. Erasing Gear Box data. a. Touch EGS Erasure. b. Touch DOWNLOAD. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 20 LAUNCH X-PROG3 c. Touch OK. d. Touch DOWNLOAD. e. Touch OK. f. Touch YES. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
-
Page 21: Engine Programming
LAUNCH X-PROG3 g. Touch YES. h. Touch OK. 3.2.3 Engine Programming The engine programming function supports engine data reading, after a new gear box is replaced, you can use engine programming function to write in the backup data. • Connecting diagnostic system for Engine programming... - Page 22 LAUNCH X-PROG3 Note: • The USB cable shown in below diagram is not included in the packing list for now, using a USB cable could effectively enhance your data transmission speed. • Vehicle engine connection could vary depending on engine types, for information how to connect the car engine, refer to the onscreen connection diagram.
- Page 23 LAUNCH X-PROG3 b. Select Engine Brand. c. Touch Search for ECU model. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 24 LAUNCH X-PROG3 d. Check ECU model (printed on the sticker on the back of your Engine), enter the engine type in the dialogue box(In example below,the engine type should be MED17.7.7). e. Touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 25 LAUNCH X-PROG3 2. Connect the engine. a. Touch View Wiring Diagram. b. Read the connection diagram, perform the proper connection based on the engine type and then touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 26 LAUNCH X-PROG3 c. Touch Read chip ID. d. When below dialogue box appears, touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 27 LAUNCH X-PROG3 3. Backup data. a. Touch Backup EEPROM Data. b. Enter the file name for EEPROM data. c. Confirm the storage path, and touch OK. d. Touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
- Page 28 LAUNCH X-PROG3 e. Follow the onscreen instructions to backup flash data also when the above is done. 4. Restore EEPROM data. Stop: The EEPROM restoration applies only when you have encountered irrevocable faults. a. Touch Restore EEPROM Data. b. Touch Backup EEPROM file name.
- Page 29 LAUNCH X-PROG3 c. Confirm the selected Backup EEPROM file, and touch OK. d. When the data is successfully restored, touch OK. www.diagtools.eu, Pernavas 43A, Riga, Latvia, LV-1009, +37129416069, info@diagtools.eu...
-
Page 30: Return From Diagnostic Function
LAUNCH X-PROG3 • 3.2.4 Return from Diagnostic Function After completion, you can press to return from programming interface. 4. Software Upgrade The software update function keeps your diagnostic software & App up-to- date, you can also use it to customize your frequently used software. -
Page 31: Warranty
LAUNCH X-PROG3 Note: • You may stop the process by tapping Stop, and tap Continue to resume the process later. • In case of network connection failure, tap Retry. 3. You will see below dialogue box once the installation is completed. - Page 32 LAUNCH X-PROG3 damages. The following cases are not covered in product warranty: • Products with mechanical serial number being altered, removed, or defected. • Products exposed to extreme conditions, such as excessive temperature, or moisture. • Products damage resulting from external causes such as fire, dirt, sand battery leakage, blown fuse, theft or improper usages of electrical source.