Page 1
® ® HYNOX 130 SINGLE PHASE HOT WATER ELECTRIC HIGH PRESSURE WATER CLEANER OPERATOR MANUAL Model Pump Working Flow Electric Burner Outlet Hot Diesel Fuel Con Approx Machine Pressure Rate Motor Type Water Temp Tank KG/H Weight Dimension LP/M Volt / Hz °C...
Page 2
OPERATOR MANUAL This page has been left blank intentionally. Jetwave Group Pty Ltd (ABN 20 056 759 892) jetwave.com.au Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
GROUP. Reproduction and divulgation, in whole or in part are prohibited by law. Where to Find Us You never have to look far to find Jetwave support and service for your pressure washer. There are many Jetwave authorised service dealers Australia wide who provide quality service.
High Pressure Hose - 10m of 3/8” double wire braided hose with quick coupling. User Manual - Hynox 130 Single Phase Hot Water Electric High Pressure Washer Warranty Card Contact your point of purchase immediately if any of the above components are missing.
4. If you require hot water operation press the Burner On/Off to the ON position and set the Thermostat to the required temperature. 5. Point the lance towards the object to be cleaned and depress the trigger on the gun. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Page 6
2 minutes to flush all detergent from unit. WARNING: Ensure that the detergent tap is turned off is there is no detergent (the pump will suck air and not work). Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
5. Ensure that the tap on the water supply is fully opened before operating the machine. 6. After chemical/detergent use, flush the facility with clean water. Figure 4 – Hynox 130 Operating Procedure Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
OPERATOR MANUAL Trouble Shooting The following table is provided as a general guide only. Please refer to your local Jetwave agent for service, repairs, parts and/or specific advice. Fault Probable Cause Possible Remedy Pump is sucking air. Check that all hoses and fittings are airtight.
Page 9
Replace the nozzle. Diesel pump damaged. Replace the diesel pump. Diesel solenoid valve damaged. Replace the diesel solenoid valve. Faulty thermostat. Check and replace. Faulty pressure switch. Check and replace. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Keep work areas cleaner – Keep hoses organised. remove grease and other Slip-proof stable footwear matter from floors. and remove grease and other matter from floors in operator’s vicinity. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Page 11
NOTE: Be aware that the onus is on the operator to be aware of Australian Standard - AS/NZS 4233.1:1999 High Pressure Water (Hydro) Jetting Systems – Part one: Guidelines for Safe Operation and Maintenance. Jetwave will not be responsible for standards not met. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Page 12
Ensure the correct PPE is Ensure everyone is a hand and that the being worn by operators safe distance from the surrounding area is a no during operation. operating machinery. smoking area. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Pump Instruction and Breakdowns General Information JETWAVE GROUP declines all liability for any damage caused by negligence or failure to respect the rules contained in this manual. 1. The STANDARD pumps work with clean, soft water, at a maximum temperature of 40°C, and, only for short periods, up to 60°C.
In no circumstances shall it be dumped in the environment. WARNING: To guarantee absolute reliability and safety, use should be made exclusively of original spare parts. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
10-second pause. 4. Complete the connections and/or install the nozzles. 5. All Jetwave Group units are tried and tested prior to shipment, the user is, however, obliged to test the complete system for an adequate time to check for leaks, overheating, deterioration in performance or calibration, etc.
Page 16
The oil in the sump of the pump is not at the required level or is not of the recommended type. The belt is too tight, the joint or the transmission is not aligned. Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Page 17
60.1205.31 Special nut, M6 brass 60.1202.84 Valve regulating knob Seat, 10mm+O-ring, 1,78mm 60.2221.20 14.3582.00 Washer, 30,5x42x2 mm NBR85+shutt. 10.4021.00 Back-up ring, opn. 11,5x15,9x1,2 mm 60.2254.31 Ring nut, M30 brass Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
Page 18
Washer Ø 21.5x27x1.5 90.3920.00 Crank Case Seal Ø 101.27 98.1966.00 Brass Plug G 1/8”x8 x2.62 (3400) 90.2617.00 V Packing Ø 15 LP 44.1600.22 Rear Cover 99.1837.00 Bolt M6x14 UNI 5931 Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...
OPERATOR MANUAL Maintenance Log Approx Hour Date Maintenance Performed Service Agent Meter Reading Jetwave Group Pty Ltd • Keswick, SA 5035 AU • jetwave.com.au...