Advertisement
安装步骤
如何安装手持花洒和软管
安装手持花洒(1)之前，先打开水源约
一分钟冲洗掉杂质。
将单向阀(2)按图示方向装入手持花洒
注意：单向阀带O型圈一端必须朝下
1
(如图示方向)。
2
根据需要将限流器(3)放入到花洒进水
3
端。注意：如水压太低，则不必安装
4
限流器。
将滤网垫片(4)放入花洒软管(5)接头内
，
连接手持花洒与软管。注意：不要过
份拧紧。软管另一端连接水源。
如何安装滑杆
在墙面上选择一个合适的位置，用于
安装滑动花洒支架。避开墙面内的电
线和管道。
根据支架座(6,7)尺寸图，在墙面适当
的高度打两个孔，将胀塞(8)分别塞入
孔中。用螺钉(9)固定上支架座(6)于墙
上。
试装支杆(10)、螺钉(11)和下支架座(7)
，
用笔标记下支架座的位置并找出两个
孔的位置，钻两个孔，塞入胀塞(8)，
用螺钉(9)固定下支架座于墙上。
将花洒挂架(12)穿过支杆(10)，并且调
节花洒挂架转钮，使其位置合适。用
螺钉(11)将支架组件固定在支架座上。
分别将支架座盖(13)通过支杆装在支架
座上，再扣上支杆盖(14)。
1473170-T2-A
INSTALLATION
How to Install the Handshower
and Hose
Before installing the handshower(1),
flush both water supplies for about one
minute to remove any debirs.
Put the check valve(2) into the
handshower. Note: Keep the O-ring of
the check valve downward.
Install the regulator(3) into the
handshower if needed. Note: If working
pressure is too low, the regulator is not
needed.
5
Put the screen washer(4) into shower
hose(5). Connect the handshower to the
shower hose. Note: Don't over tighten.
Connect another end of shower hose to
the water supply.
How to Install the Slide bar
21.7mm
Decide on a suitable position for the
slide bar avoiding buried cables and
pipes in the wall.
Drill two holes at the proper height in
21.3mm
the wall as the bracket(6,7) dimensions.
Put the anchors(8) into the holes. Install
the bracket(6) with the screws(9) in the
wall.
Rehearse the slide bar(10), screws(11)
and bracket(7). Mark the outline of the
bracket with a pencil on the wall, and
find the position of the holes. Drill two
holes and put the anchors(8) into the
holes. Install the bracket(7) with the
screws(9) in the wall.
Slide the handshower holder(12) onto
the bar(10). Adjust the holder to the
proper position. Tighten the slide bar kit
with the screws(11).
Slide the bracket covers(6) onto the
slide bar, and install the covers(7).
维护与保养
如何维护保养手持花洒
喷孔杂质或结垢会导致水流变形，流量变
小。打开水源，用力按压或摩擦橡胶喷
孔，去除杂质或水垢。
取下软管接头内的滤网垫片，去除杂质。
清洗说明
适用于所有加工处理过的表面：以中性肥皂水清洗
镀层表面，再以干净的软布彻底擦干整个表面，许
多清洁剂，比如氨水、去污粉及洁厕灵等，会对电
镀表面造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌
的水龙头及其配件上。
2
1473170-T2-A
CARE AND MAINTENANCE
How to Maintain the Handshower
Any debris or mineral build-up may cause
the flow stream to become distorted or
reduce the flow rate. To remove debris or
mineral build-up, run water through the
handshower, firmly press or rub your finger
back and forth across the rubber nozzles.
Remove and clean the screen washer.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals,
such as ammonia, chlorine, toilet cleaner etc．which
could adversely affect the finish and are not
recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
3
Advertisement
