Before Starting The Equipment - EINHELL TE-OS 2520 E Operating Instructions Manual

Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ........................ 82 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 93 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muffs.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specified during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_TE_OS_2520_E_SPK9.indb 16 Anl_TE_OS_2520_E_SPK9.indb 16
= 7.092 m/s
2
h
2
GB
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the dust collection box (Fig. 2)
The dust collection box (6) must be pushed onto
the connector for the dust collection box (5). Push
the dust collection box (6) onto the equipment
until you hear it click clearly. To remove the dust
collection box (6), press the locking knob (7) and
pull the dust collection box to the rear and off.
The dust is extracted directly through the abrasive
paper and the grinding/sanding disk into the dust
bag.
Important!
For health safety reasons it is imperative that
you use the dust collection box.
5.2 Fastening the grinding/sanding paper
with the Velcro fastening system (Fig. 3-6)
Only use grinding/sanding paper with the corres-
ponding dimensions and matching perforations!
•
Lift the clamping lever (8) on the front of the
orbital grinder/sander.
•
Insert the grinding/sanding paper into the
open clamp and close the lever.
•
Lay the grinding/sanding paper over the os-
cillating plate (1) so that the paper is taut and
clamp it again at the back of the orbital grin-
der with the second clamping lever (8).
•
Make sure that the perforations in the san-
ding/grinding paper coincide with the oscilla-
- 16 -
23.03.2022 08:58:32 23.03.2022 08:58:32