Volume Measurement - BorMann PRO BDM6500 User Manual

EN
While charging, the device may heat up, this
Is normal, and will not affect the product performance
and lifetime.
Please unplug the charger and take off the batteries
when not In use.
Technical Data
*(BDM6500 \ BDM7000)
Measuring Range: *0.2-60m \ 0.2-100m
Measuring Accuracy: +/-2mm
Single Distance
Measurement:
Continuous
Measurement:
Area Measurement:

Volume Measurement:

Pythagoras (2-point):
Pythagoras (3-point):
①
Pythagoras (3-point):
②
Auto Level:
Auto Height:
Add/Subtract:
Tilt Sensor:
Measuring Units: m/ft/in/ft+in
Screen Display: 2-inch white-on-black
Protection Class: IP65
Laser Class: Class 2
Laser Type: 630-670nm, <1mW
Battery Type: NI-MH rechargeable
batteries charged via
USB port
1. Measuring Range
The Maximum range shall be different according
to different models. The actual range refers to the
package.
2.Measuring Accuracy (''D" stands for measured
distance)
If measuring under favourable conditions, such as
smooth surface, proper temperature and indoor
lighting, the device is able to work within certain range
as declared.
Maximum deviation occurs under unfavourable
conditions such as bright sunlight or when measuring
to poorly reflecting or very rough surfaces.
3. Tilt Measurement Accuracy
0.1° is caused by temperature, D is +/- 0~45°, e.g.: at
normal temperature the accuracy is +/-0.3° at angle of
0° , at abnormal temperature the accuracy is +/-0.85°
at angle of 45°.
Tips: In case of bright sunlight and bad reflection of the
object, please use the target plate or reflector.
3
Operating Instructions
The Single distance measurement prompt when it is
switched ON, press to select measuring mode, and
the flashing line reminds user to get the newest result.
Front Tripod
The measuring data should be different due to
different Reference settings.
Single Distance Measurement
The device will come to Single distance measurement
when it is switched ON.
Press after aiming at target to get result in
summary line.
Continuous Measurement
Long press to activate Continuous
measurement , sweeping slowly the laser
back and forth and up and down over the desired
target point from a fixed measuring point, then press
to stop, the value for Maximum and Minimum
distances are displayed in the screen as wall as the last
measured value marked in the summary line. You can
choose Max or Min value according to your needs.
*This function will be stopped automatically after 5
minutes of inactivity.
Area Measurement
Press to select Area measurement mode
According to reminding of the flashing line, press
to get the distance for 1st line (Length), press
for 2nd line (Width), the Area is calculated and displayed
in the summary line.
Volume Measurement
Press to select Volume measurement mode
According to reminding of the flashing line, press
to get the distance for 1st line(Length), press
for 2nd line(Width), press third time for 3rd line(Height),
the Volume is calculated and displayed in the summary
line.
WWW.BORMANNTOOLS.COM
Rear
Pythagoras 2 point
Refer to figure ①. Press
mode
line, press
change to the horizontal direction of the object
from the fixed measuring point, press
again to get the distance of 2nd line, the result is
displayed in the summary line.
Pythagoras 3 point ①
.
again
Refer to figure ②. Press
mode
line, aiming at the first point press
the distance of 1st line, change to the horizontal
direction of the object from the fixed measuring
point, press
line, move to the 2nd target point, press
First Distance
get the distance of 3rd line, the result is displayed
in the summary line.
Second Distance
Circumference
Area
.
again
First Distance
Second Distance
Third Distance
Volume
to select Pythagoras
. According to reminding of the flashing
to get the distance of 1st line,
First Distance
Second Distance
Result
to select Pythagoras
. According to reminding of the flashing
to get
again to get the distance of 2nd
First Distance
Second Distance
Third Distance
Result
to