Installation Instructions - Bertazzoni Master Series User Instructions

hood is operating.
B) Do not touch bulbs or adja-
cent areas, during or straight
after prolonged use of the
lighting installation.
C) Flambè cooking is prohibited
underneath the cooker hood.
D) Avoid free flame, as it is
damaging for the filters and a
fire hazard.
E) Constantly check food frying
to avoid that the overheated oil
may become a fire hazard.
F) Disconnect the electrical
plug prior to any maintenance.
G) This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
i f t h e y h ave b e e n g i ve n
supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by children w
thout supervision.
H) Young children should be
supervised to ensure they do
not play with the appliance.
I) There shall be adequate ven-
tilation of the room when the
rangehood is used at the same
time as appliances burning gas
or other fuels.
L) There is a risk of fire if clean-
ing is not carried out in accord-
ance with the instructions.

INSTALLATION INSTRUCTIONS

• Assembly and electrical con-
nections must be carried out by
specialised personnel.
• Wear protective gloves before
proceeding with the installa-
tion.
• Electric Connection (Fig.10):
This is a class I, appliance and must therefore be connected to
an effiecient earthing system.
- The appliance must be connected to the electricity supply as
follows:
BROWN = L line
BLUE = N neutral
YELLOW/GREEN =
The neutral wire must be connected to the terminal with the
N symbol while the YELLOW/GREEN, wire must be connected
to the terminal by the earth symbol
When connecting the appliance to the electricity supply, make
sure that the mains socket has an earth connection. After fitting
the ducted cooker hood, make sure that the electrical plug is
in a position where it can be accessed easily. If the appliance
is connected directly to the electricity supply, an omnipolar
switch with a minimum contact opening of 3 mm must be
placed in between the two; its size must be suitable for the
load required and it must comply with current legislation.
• If the hob is electric, gas, or induction, the minimum distance
between the same and the lower part of the hood must be at
least 65 cm (Fig.11). If a connection tube composed of two
parts is used, the upper part must be placed outside the lower
part. Do not connect the cooker hood exhaust to the same
conductor used to circulate hot air or for evacuating fumes
from other appliances generated by other than an electrical
source. Before proceeding with the assembly operations,
remove the anti-grease filter(s) (Fig.6) so that the unit is easier
to handle.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air (Fig.1B).
• We recommend the use of an air exhaust tube which has
the same diameter as the air exhaust outlet hole (Ø 150mm).
If a pipe with a smaller diameter is used, the efficiency of the
product may be reduced and its operation may become noisier.
• Fixing to the wall:
Drill the holes A respecting the distances indicated (Fig.2). Fix
the appliance to the wall and align it in horizontal position
to the wall units. When the appliance has been adjusted,
definitely fix the hood using the screws X (Fig.5). For the
various installations use screws and screw anchors suited to
the type of wall (e.g. reinforced concrete, plasterboard, etc.). If
the screws and screw anchors are provided with the product,
check that they are suitable for the type of wall on which the
hood is to be fixed.
• Fixing the decorative telescopic flue:
Arrange the electrical power supply within the dimensions of
the decorative flue. If your appliance is to be installed in the
ducting version, prepare the air exhaust opening. Install the
upper decorative flue's support bracket and fix it on the wall
using the screws A (Fig.3) so it is in axis with your hood and re-
specting the distance from the ceiling shown in Fig.2. Connect
flange C to air extraction hole via an air extraction pipe (Fig.5).
ATTENTION:
only for models KPH120MASXT - KPH120MASNET before
installing the decorative chimneys, mount the bracket on the
upper chimney as shown in figure 2A.
Insert upper decorative flue inside the lower decorative flue
and rest them on top of the frame. Extract the upper flue up
to the bracket and fix it with the screws B (Fig.3). To transform
the hood from a ducting version into a filtering version, ask
your dealer for the charcoal filters and follow the installation
instructions.
- 14 -
earth.
.