jbc ALS Instruction Manual

jbc ALS Instruction Manual

Stand for al250 auto-feed iron

Advertisement

Quick Links

INSTRUCTION MANUAL
ALS / ALES
Stand for AL250 Auto-Feed Iron

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ALS and is the answer not in the manual?

Questions and answers

Summary of Contents for jbc ALS

  • Page 1 INSTRUCTION MANUAL ALS / ALES Stand for AL250 Auto-Feed Iron...
  • Page 2: Packing List

    This manual corresponds to the following references: AL-SG ALE-SA works with control unit AL works with control unit ALU Packing List Included in AL-SG box: Included in ALE-SA box: Stand for Stand for AL250 Auto-Feed Iron ....... 1 unit AL250 Auto-Feed Iron ...... 1 unit Included in both, AL-SG and ALE-SA box: Sponge for Modular Brass Wool ....
  • Page 3: Features And Connections

    w w w.jbctools.com Features and Connections The stand includes a sleep mode that automatically reduces the tip temperature when the tool is in the stand. Adjustable Cartridge Storage Cable Collector Ref. CC1001 Quick Tip Changer Ajustable Tool Holder Brass Wool (inside) Wiper for Sponge...
  • Page 4 Assembly Cable Collector and Adjustable Tool Holder The cable collector is flexible. It accompanies and adapts to the movements during the Insert the cable into the clip soldering process. and then insert into the cable collector. Do not leave the cable longer than necessary to reach the work area freely.
  • Page 5: Changing Cartridges

    w w w.jbctools.com Changing Cartridges For a safe cartridge change, unplug the tool or turn the station off before following these guidelines. AL250 1. Unlocking 2. Removing AL250-B 0.9-1 Ø 0.9-1 Ø 0.9-1 Ø Loosen the cartridge screw (1) to release the Place the cartridge in the quick tip changer cartridge (2).
  • Page 6 Replacing Guide Sets Once the tool is disconnected from the control unit and has cooled down, follow these instructions: Disassemble the outlet nozzle (1) from the guide set. Loosen the guide set screw (2), take out the guide set (3) and insert the desired one. Put the outlet nozzle (1) back on again.
  • Page 7: Maintenance

    - Check periodically that the metal parts of the tool/stand are clean so that the station can check the tool’s status. - Periodically check all cables and tube connections. - Replace any defective or damaged parts. Use original JBC spare parts only. Repairs should only be performed by a JBC authorized technical service. Clean periodically...
  • Page 8 Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the stand for any purpose other than soldering or rework. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use.
  • Page 9 w w w.jbctools.com Notes...
  • Page 10 Notes...
  • Page 11: Specifications

    w w w.jbctools.com Specifications Stand for AL250 Auto-Feed Iron Ref.: AL-SG - Includes Sleep function - Total Net Weight 1946 g / 4.29 lb - Package Dimensions / Weight: 342 x 155 x 120 mm / 1476 g (L x W x H) 13.46 x 6.10 x 4.72 in / 3.25 lb ALES Stand for ALE250 Auto-Feed Iron...
  • Page 12 Warranty JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.

This manual is also suitable for:

AlesAl-sgAle-sa

Table of Contents