Programme - Bosch HB Series User Manual And Installation Instructions

en Programme
a The appliance starts heating after a few seconds.
The cooking time counts down in the display.
a Once the cooking time has elapsed, a signal
sounds and the appliance stops heating. "Operation
finished" is shown in the display.
When your food is ready, use ​ ⁠ to switch off the ap-
4.
pliance.
Changing the cooking time
You can change the cooking time at any time.
Requirement: ​ ⁠ is highlighted in the display.
Use the temperature selector to change the cooking
▶
time.
a The appliance applies the change after a few
seconds.
Cancelling the cooking time
You can cancel the cooking time at any time.
Requirement: ​ ⁠ is highlighted in the display.
Use the temperature selector to reset the cooking
▶
time to zero.
a After a few seconds, the appliance applies the
change and continues to heat without a cooking
time.
9.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡ Food will spoil if you leave it in the cooking com-
partment for too long.
¡ Food will spoil if you leave it in the cooking com-
partment for too long.
10 Programme
The programmes help you to use your appliance to
prepare different dishes by selecting the optimum set-
tings automatically.
10.1 Cookware for programmes
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300 °C.
Glass or glass ceramic cookware is best. The joint
should cover approx. two thirds of the cookware base.
Cookware made from the following material is not
suitable:
¡ Bright, shiny aluminium
¡ Unglazed clay
¡ Plastic or plastic handles
10.2 Preparing food for the programme
Use fresh and, ideally, chilled food. Use frozen food
straight from the freezer.
Weigh the food.
1.
The weight of the food is required in order to cor-
rectly set the programme.
Add the food to the cookware.
2.
12
Requirements
¡ The type of heating and temperature are set.
¡ A cooking time is set.
Touch the ​ ⁠ button.
1.
Use the function selector to select the end time ​ ⁠ .
2.
Use the temperature selector to set the end time.
3.
a The display shows the calculated end time.
Press the ​ ⁠ button to confirm.
4.
a After a few seconds, the appliance applies the set- 5.
ting and the display shows the set end time.
a Once the calculated start time has been reached,
the appliance starts heating up and the cooking
time starts counting down.
When the cooking time has elapsed:
6.
An audible signal sounds and "Operation fin-
‒
ished" is shown in the display.
When your food is ready, use ​ ⁠ to switch off the
‒
appliance.
Changing the end time
You can also change the end time while the oven is
operating. The operation is then stopped and restarts
in accordance with the set cooking time and end time.
Requirement: ​ ⁠ is highlighted in the display.
Use the temperature selector to delay the end time.
▶
a The appliance applies the change after a few
seconds.
Cancelling the end time
You can delete the set end time at any time.
Requirement: ​ ⁠ is highlighted in the display.
Use the temperature selector to reset the end time
▶
to the current time plus the set cooking time.
a After a few seconds, the appliance applies the
change and starts heating up. The cooking time
counts down.
3. Place the cookware onto the wire rack.
Always place the cookware into the cooking com-
partment while it is cold.
10.3 Setting a programme
The appliance selects the optimal type of heating, tem-
perature and cooking time. All you need to do is set
the weight.
Notes
¡ You can set the weight only in the intended range.
¡ After the programme starts, you can no longer
change the programme and the weight.
1. Touch the ​ ⁠ button.
Use the function selector to set the required pro-
2.
gramme.
Use the temperature selector to set the weight of
3.
your food. Always set the next higher weight.
Touch the ​ ⁠ button.
‒
A message appears.
‒
4. Touch the ​ ⁠ button.
A message appears.
a After a few seconds, the programme starts and the
cooking time counts down.