Tone Control Sub-Menu; Intellivolume Sub-Menu; Trigger Sub-Menu - Integra DTR-7.1 Owner's Manual

Input Setup

2-4. Tone Control sub-menu

This sub-menu allows you to increase or decrease the volume for
only the low (bass) or high (treble) frequency sounds. This sub-
menu does not appear if "Direct" or "THX" are selected as the
listening mode.
Menu
1.Speaker Setup
2.Input Setup
2.Input Setup
Input:DVD
3.Listening Mode Setup
4.Preference
a.Audio Setup 2-4.Tone Control
5.OSD Setup
b.Video Setup
Input:DVD
c.Listening Mode Preset
d.Tone Control
a.Bass
e.IntelliVolume
f.12V Trigger
b.Treble
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
a. Bass
Press the cursor button to decrease the bass sounds and press the
cursor button to increase the bass sounds. The bass can be
adjusted between –12 and +12 decibels in two steps.
b. Treble
Press the cursor button to decrease the treble sounds and press
the cursor button to increase the treble sounds. The treble can be
adjusted between –12 and +12 decibels in two steps.
40
: 0dB
: 0dB
Quit:|OSD|

2-5. IntelliVolume sub-menu

When switching input sources, you may find that the output level
for different components or input sources connected to the DTR-
7.1 is different even though the main volume setting is the same.
Under normal circumstances, you would then have to change the
volume setting each time you change the input source. This
IntelliVolume sub-menu allows you to preset a volume level for
each input source separately so that when you do switch from one
input source to another, the DTR-7.1 adjusts the volume
accordingly so that the resulting volume stays the same. To set the
IntelliVolume, simply select an input source at the front panel, and
if that source is quieter than other sources, increase its decibel
level with the cursor button, or if it is louder than other sources,
decrease its decibel level with the
The IntelliVolume can be adjusted between –12 and +12 decibels.
Menu
1.Speaker Setup
2.Input Setup
2.Input Setup
Input:DVD
3.Listening Mode Setup
4.Preference
a.Audio Setup
2-5.IntelliVolume
5.OSD Setup
b.Video Setup
Input:OPT1
c.Listening Mode Preset
d.Tone Control a.IntelliVolume
e.IntelliVolume
f.12V Trigger
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
2-6. 12V Trigger sub-menu
This sub-menu allows you to make the required settings to turn on
the output from the 12V TRIGGER terminal to control another
component or device with the DTR-7.1 for each input source.
Menu
1.Speaker Setup
2.Input Setup
2.Input Setup
Input:DVD
3.Listening Mode Setup
4.Preference
2-6.12V Trigger a.Audio Setup
5.OSD Setup
b.Video Setup Input:DVD
c.Listening Mode Preset
d.Tone Control a.12V Trigger A
e.IntelliVolume b.12V Trigger B
f.12V Trigger
|ENTER| Quit:|OSD|
|ENTER| Quit:|OSD|
a. 12V Trigger A
On: Select to activate the device connected to the 12V TRIGGER
A terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER A
terminal or you do not want the connected device to activate.
b. 12V Trigger B
On: Select to activate the device connected to the 12V TRIGGER
B terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER B
terminal or you do not want the connected device to activate.
cursor button.
: 0dB
Quit:|OSD|
:Off
:Off
Quit:|OSD|