Advertisement
3. Feed the paper until its leading edge gets pulled in.
Warning—Potential Damage: To avoid paper jams, do
not force paper into the manual feeder.
S S e e t t t t i i n n g g t t h h e e P P a a p p e e r r S S i i z z e e a a n n d d T T y y p p e e
1. From the control panel, navigate to Settings > Paper > Tray
Configuration > Paper Size/Type, then select a paper source.
For non-touch-screen printer models, press
through the settings.
2. Set the paper size and type.
U U p p d d a a t t i i n n g g F F i i r r m m w w a a r r e e
Some applications require a minimum device firmware level to
operate correctly.
For more information on updating the device firmware, contact your
customer service representative.
1. Open a web browser, and then type the printer IP address in the
address field.
• View the printer IP address on the printer home screen. The IP
address appears as four sets of numbers separated by periods,
such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the web page correctly.
2. Click Settings > Device > Update Firmware.
3. Choose one of the following:
• Click Check for updates > I agree, start update.
• Upload the flash file. To upload the flash file, perform the
following steps.
To get the latest firmware, go to www.xerox.com, and search for
your printer model.
1. Browse to the flash file.
Make sure that you have extracted the
Note:
firmware zip file.
2. Click Upload > Start.
C C o o n n n n e e c c t t i i n n g g t t h h e e P P r r i i n n t t e e r r t t o o a a W W i i - - F F i i N N e e t t w w o o r r k k
Before you begin, make sure that:
• Active Adapter is set to Auto. From the home screen, touch
Settings > Network/Ports > Network Overview > Active Adapter.
• The Ethernet cable is not connected to the printer.
U U s s i i n n g g t t h h e e W W i i r r e e l l e e s s s s S S e e t t u u p p W W i i z z a a r r d d i i n n t t h h e e P P r r i i n n t t e e r r
Before using the wizard, make sure that the printer firmware is
to navigate
updated. For more information, refer to
1. From the home screen, touch the Wifi button, then select Set up
now.
2. Select a Wi-Fi network, and then type the network password.
3. Touch Done.
U U s s i i n n g g t t h h e e S S e e t t t t i i n n g g s s M M e e n n u u i i n n t t h h e e P P r r i i n n t t e e r r
1. From the home screen, touch Settings > Network/Ports >
Wireless > Setup On Printer Panel > Choose Network.
2. Select a Wi-Fi network, then type the network password.
Note:
For Wi-Fi-network-ready printer models, a prompt to
set up the Wi-Fi network appears during initial setup.
C C o o n n f f i i g g u u r r i i n n g g W W i i - - F F i i D D i i r r e e c c t t
Wi-Fi Direct is a Wi-Fi-based peer-to-peer technology that allows
wireless devices to connect directly to a Wi-Fi Direct-enabled printer
without using an access point (wireless router).
1. From the home screen, touch Settings > Network/Ports > Wi-Fi
Direct.
2. Configure the settings.
• Enable Wi-Fi Direct—Enables the printer to broadcast its own
Wi-Fi Direct network.
• Wi-Fi Direct Name—Assigns a name for the Wi-Fi Direct
network.
• Wi-Fi Direct Password—Assigns the password for negotiating
the wireless security when using the peer-to-peer connection.
• Show Password on Setup Page—Shows the password on the
Network Setup Page.
• Auto-Accept Push Button Requests—Lets the printer accept
connection requests automatically.
• By default, the Wi-Fi Direct network password is not visible on
Updating
Firmware.
the printer display. To show the password, enable the
password peek icon. From the home screen, touch Settings >
Security > Miscellaneous > Enable Password/PIN Reveal.
• To know the password of the Wi-Fi Direct network without
showing it on the printer display, from the home screen touch
Settings > Reports > Network > Network Setup Page.
C C o o n n n n e e c c t t i i n n g g a a C C o o m m p p u u t t e e r r t t o o t t h h e e P P r r i i n n t t e e r r
Before connecting your computer, make sure that Wi-Fi Direct has
been configured. For more information, see
F F o o r r W W i i n n d d o o w w s s U U s s e e r r s s
1. Open the printers folder.
2. Select the printer you want to update, and then do either of the
following:
• For Windows 7 or later, select Printer properties.
• For earlier versions, select Properties.
12
Note:
Accepting push-button requests automatically is
not secured.
Note:
Notes:
Configuring Wi-Fi
Direct.
Advertisement
