Barco iCon H250 Installation Manual
  1. Manuals
  2. Brands
  3. Barco Manuals
  4. Computer Hardware
  5. iCon H250
  6. Installation manual
Barco iCon H250 Installation Manual

Barco iCon H250 Installation Manual

Dvi hdcp input kit
Hide thumbs Also See for iCon H250:
Table of Contents

Advertisement

Quick Links

Download this manual
DVI HDCP Input Kit
Installation manual
iCon H250/H500, iD H250/H500, NH-12, Galaxy NH-12
R9843045
R59770246/00
28/04/2008

Advertisement

Table of Contents
loading

Related Manuals for Barco iCon H250

Summary of Contents for Barco iCon H250

  • Page 1 DVI HDCP Input Kit Installation manual iCon H250/H500, iD H250/H500, NH-12, Galaxy NH-12 R9843045 R59770246/00 28/04/2008...
  • Page 2 Barco nv Presentations Noordlaan 5, 8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.35.86.51 E-mail: presentations.bid@barco.com Visit us at the web: www.barco.com Printed in Belgium...
  • Page 3 The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.

  • Page 5: Table Of Contents

    Installing an optional input layer ..................... 9 4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 ........13 Removing the PMP .
  • Page 6 Table of contents R59770246 DVI HDCP INPUT KIT 28/04/2008...

  • Page 7: Safety

    1. Safety 1. SAFETY Safety warnings ARNING This procedure is intended for use only by BARCO authorized technicians. ARNING Be sure that the projector is powered down and that the power cord is removed from the wall outlet. Wait until the projector is cooled down before starting the procedure.
  • Page 8 1. Safety R59770246 DVI HDCP INPUT KIT 28/04/2008...

  • Page 9: Introduction

    The board can be mounted in a free slot of the projector’s input module (NH-12; Galaxy NH-12) or will replace the existing DVI input board (iCon H250/H400/H500; iD H250/H500). The signal of a source connected to the DVI HDCP input board will not be displayed on the DVI output.

  • Page 10: Assembling The Dvi Hdcp Input Board

    2. Introduction Image 2-1 Image 2-2 DVI HDCP input board Front plate (NH-12; Galaxy NH-12) Image 2-3 Image 2-4 Image 2-5 Front bolt Fixation nut Bottom screw Image 2-6 Side screw Assembling the DVI HDCP input board Necessary tools Torx screwdriver T10 How to assemble the DVI HDCP input board? 1.
  • Page 11 2. Introduction Image 2-7 Tip: Do not fix the front plate to the DVI HDCP input board yet! R59770246 DVI HDCP INPUT KIT 28/04/2008...
  • Page 12 2. Introduction R59770246 DVI HDCP INPUT KIT 28/04/2008...

  • Page 13: Installation In The Nh-12 And In The Galaxy Nh-12

    3. Installation in the NH-12 and in the Galaxy NH-12 3. INSTALLATION IN THE NH-12 AND IN THE GALAXY NH-12 In the Galaxy NH-12 the DVI HDCP input board will be mounted in the free slot. In the NH-12 the DVI HDCP input board can be mounted in one free slot or the other.
  • Page 14 3. Installation in the NH-12 and in the Galaxy NH-12 Image 3-3 Optional input layer: cover removed 3. Insert the optional input layer in the input module 4. Push the optional input board to the left side to plug in the board-to-board connectors to the PMP Image 3-4 Image 3-5 PMP: board-to-board connectors for optional input board...
  • Page 15 3. Installation in the NH-12 and in the Galaxy NH-12 Image 3-7 7. Fix the front panel to the input module using the fixation screws Image 3-8 Position of the fixing screws 8. Install the covers (see concerning chapters) front cover rear cover R59770246 DVI HDCP INPUT KIT 28/04/2008...
  • Page 16 3. Installation in the NH-12 and in the Galaxy NH-12 R59770246 DVI HDCP INPUT KIT 28/04/2008...

  • Page 17: Installation In The Icon H250/H400/H500 And In The Id H250/H500

    4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 4. INSTALLATION IN THE ICON H250/H400/H500 AND IN THE ID H250/H500 The software version of the projectors must be 1.30 or higher. Lower versions do not support this DVI HDCP input board! The iCon H400 is replaced by the iCon H500 and will not be mentioned in the procedure.
  • Page 18 H250/H500: fixing bolts of the front plate upper part 3. Remove the upper part of the front panel 4. Unplug connector J110 (cable coming from the SBC) — ONLY FOR ICON H250/H500 Image 4-3 iCon H250/H500 ONLY: unplug connector J110 on the PMP 5.

  • Page 19: Removing The Input Module

    4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 Image 4-6 PMP flipped over Removing the input module Necessary tools Phillips screwdriver Ph1 — long model How to remove the input module? 1. Remove the pixel map processor (PMP) — See the concerning chapter.

  • Page 20: Replacing The Dvi / D15 Input

    4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 Replacing the DVI / D15 input Necessary tools • Screwdriver Torx T10 • nut spanner 5 mm How to replace the DVI / D15 input? 1. Remove the input module — See the concerning chapter.

  • Page 21: Installing The Dvi Hdcp Input Layer

    4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 Image 4-11 Disconnect the backplane Image 4-12 Backplane disconnected 5. Take out the DVI / D15 input board Installing the DVI HDCP input layer How to install the DVI HDCP input layer? 1.
  • Page 22 4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 R59770246 DVI HDCP INPUT KIT 28/04/2008...

  • Page 23: Index

    9, 13 removing 13, 15 in the Galaxy NH-12 input module in the iCon H250 in the iCon H400 replacing in the iCon H500 DVI / D15 input in the iD H250 in the iD H500 in the NH-12...

This manual is also suitable for:

Icon h500Id h250Id h500Nh-12Galaxy nh-12

Table of Contents