Table of Contents
Advertisement
Quick Links
Parts Supplied
Table 1
Part
Screw: Mach M4 x 0.7, 20 mm, LG T-20 Pan HD SST
Rod base plate
Rod hook plate
Flange support spacer
Rod
Removable oven door (not shown)
Parts Identification
Rod
Agilent G3430-68640 Removable Oven Door
Accessory
Installation Guide
Parts supplied
Part number
0515-0686
G3430-00646
G3430-00647
G3430-20645
G3430-20643
G3430-60640
Agilent Technologies
Quantity
1
1
1
1
1
1
M4 screw
Flange support spacer
Rod hook plate
Rod base plate
Advertisement
Table of Contents
Related Manuals for Agilent Technologies G3430-68640
Summary of Contents for Agilent Technologies G3430-68640
- Page 1 Agilent G3430-68640 Removable Oven Door Accessory Installation Guide Parts Supplied Table 1 Parts supplied Part Part number Quantity Screw: Mach M4 x 0.7, 20 mm, LG T-20 Pan HD SST 0515-0686 Rod base plate G3430-00646 Rod hook plate G3430-00647 Flange support spacer...
-
Page 2: Tools Required
If necessary, remove any automatic liquid sampler (ALS) devices and disconnect any transfer lines from your GC inlets. Refer to your relevant instrument documentation for details. Remove any mounting posts from the inlet top cover. G3430-68640 Removable Oven Door Accessory Installation Guide... - Page 3 Remove all T- 20 Torx screws securing the inlet top cover to the GC (Figure 1). Figure 1 Remove all T-20 Torx screws Remove the inlet cover from the GC and set it aside. Be careful to not damage any gas lines during removal. G3430-68640 Removable Oven Door Accessory Installation Guide...
-
Page 4: Remove The Oven Door
Using needle nose pliers, grip the rod as shown in Figure 2, then pull up on the rod and hold. Figure 2 Pulling the rod up using needle nose pliers G3430-68640 Removable Oven Door Accessory Installation Guide... - Page 5 Continue to unscrew the rod using the T- 20 Torx driver, and remove it from the GC. Be sure to hold the door when removing the rod to avoid dropping the door. Remove the oven door from the GC. G3430-68640 Removable Oven Door Accessory Installation Guide...
- Page 6 From the top of the rod, use a T- 20 Torx driver to completely unscrew the rod and remove it from the GC. Be sure to hold the door when removing the rod to avoid dropping the door. Remove the oven door from the GC. G3430-68640 Removable Oven Door Accessory Installation Guide...
- Page 7 Use the supplied M4 screw to attach the hook plate onto the base plate as shown in Figure 6. Be sure to only engage one or two threads of the screw. Figure 6 Preparing the base plate and hook plate for installation G3430-68640 Removable Oven Door Accessory Installation Guide...
- Page 8 Figure 8. Base plate installed Hook plate latched onto instrument base Instrument base Figure 8 Underside of GC with base plate installed G3430-68640 Removable Oven Door Accessory Installation Guide...
- Page 9 (Figure 10). Figure 9 Installing the flange support spacer Figure 10 Flange support spacer orientation G3430-68640 Removable Oven Door Accessory Installation Guide...
- Page 10 Thread the door pin into in the flange support until tight. Figure 11 Installing the oven door pin Note that the pin may appear slightly canted. This does not affect the door functionality. G3430-68640 Removable Oven Door Accessory Installation Guide...
- Page 11 Tilt the top corner of the oven door towards the GC, then retract the upper hinge pin. Continue to push the door towards the GC until the upper hinge pin can be released into the upper GC hinge (Figure 13). Figure 13 Upper door hinge installed G3430-68640 Removable Oven Door Accessory Installation Guide...
-
Page 12: Complete The Installation
Open the door, then pull the top hinge lever down and tilt the top of the door out to release the top pin from the hinge. Using both hands, carefully lift off the door from the lower oven door pin and remove the door from the GC. G3430-68640 Removable Oven Door Accessory Installation Guide... - Page 13 G3430-68640 Removable Oven Door Accessory Installation Guide...
-
Page 14: Agilent Technologies
© Agilent Technologies, Inc., 2013 Printed in USA or China First edition, January 2013 Agilent Technologies, Inc.