Table of Contents
Related Manuals for DIGITECH Audio AR-1733
Summary of Contents for DIGITECH Audio AR-1733
- Page 1 WORLD BAND RADIO AR-1733 FM/MW/LW/SW/AIR Band Radio with LCD display OWNER’S MANUAL Distributed by: Electus Distribution Pty Ltd 320 Victoria Rd Rydalmere NSW 2116 Australia Ph:1300 738 555 Fax:1300 738 500 www.electusdistribution.com.au...
-
Page 3: Safety Instructions
______________________________________________________________________ WARNING Do not expose this appliance to rain or moisture Do not submerge or expose to water Protect from high humidity and rain Only operate within specified temperature range (0℃ to 40℃) Unplug immediately if liquid has been spilled or objet have falle into the ... -
Page 4: Quick Start Guide
Quick Start Guide 1. Install 2 AA batteries in the battery compartment and pay attention to the polarity of batteries’ + and – ends 2. Turn on the radio by pressing the ”POWER” button 3. Adjust ”Volume” 4. Select band by pressing the BAND button 5. -
Page 5: Table Of Contents
Table of Contents Safety Instructions……………………………. 3 Quick Start Guide……………………………..4 Radio View……………………………………..6-9 Functions and Operation Explained Power/Sleep Button…………………10 Tuning Knob………………………….10 Lock button…………………………..10 UP and Down Buttons………………11 AM BW Button……….......11 PAGE Button/Setting the alarm…...11 RESET…………………………………12 METER Button/Charging function..12 LIGHT………………………………….12 Band Button………………………….12 “0” KEY Button………………………13 0-9 KEYS………………………………13 “FREQ”UENCY Button……………...13 LCD DISPLAY…………………………13... -
Page 6: Radio View
Radio View – Front View FM/A M/SW/LW/A IR DSP RECEIVER 12/24h AM BW FM ST . PAGE ALARM charge meter A I R S QUELC H T . SET 9/10kHz AR-1 73 3 FREQ BA N D memory Power and Sleep button ○... - Page 7 Radio View – LCD Display Battery Level indicator,flashing indicates batteries are low ○ Page Number (0-9) ○ Indicates memory channel number (0-9) for Memory Stations ○ Air Squelch display ○ Indicates Signal Strength Level ○ Indicates Frequency Step (Stop/Slow/Stop) ○ kHz indicates Kilohertz while in MW and SW bands only ○...
- Page 8 Radio View – Sides View TUNING VOLUME US B Carry hand hole ○ Earphone jack (3.5mm) ○ USB power jack, Battery Charge USB jack,5 Volts ○ Tuning Knob adjusts Frequency ○ Volume Up and Down ○...
- Page 9 Radio View – Back View Whip Antenna used for FM and SW bands ○ Battery Compartment location,insert 2 “AA” batteries ○ Reset Hole for reseting radio (located on bottom of radio) ○...
-
Page 10: Functions And Operation Explained
Functions and Operation Explained Power/Sleep Button When you press the “POWER” button the first time, you will see “on” displayed for about two seconds. Press the “Power” button again To turn the radio off. To set a “SLEEP”,press and hold down “POWER” button for about two seconds. -
Page 11: Up And Down Buttons
in the LCD; press and hold down this button for three seconds to unlock all buttons,the lock icon will disappear. UP and DOWN Button These buttons can be used to tune the radio one step at a time or “press and hold” to scan for the next strong station. While the radio is on, quickly press the button to increase or de- crease frequency at the following steps: FM at 100kHz step... -
Page 12: Reset
You press the button in the first time, the “PAGE” icon will flash for about 5 seconds. You can select 0~9 pages with 0~9 keys during this period. Then press 0~9 keys to enter the channel number of a station you memorized. If there is not any operation,the “PAGE”... -
Page 13: 0" Key Button
“0” KEY Button The button can be pressed and held for two seconds to change MW step at 9kHz and 10kHz. “FREQ”UENCY Button This button is used to enter a frequency directly. You have to be in the radio band of your choice before you enter a frequency. -
Page 14: Technical Specifications
Technical Specifications 1. Frequency Coverage: 87.5 ~ 108 MHz AM(MW) 522 ~ 1620 kHz (9k step) 520 ~ 1710 kHz (10k step) 2300 ~ 26100 kHz 153 ~ 279 kHz 118 ~ 137 MHz 2. S/N (Signal to Noise) Sensitivity: >3uV >0.5mV/m >10mV/m...
Need help?
Do you have a question about the AR-1733 and is the answer not in the manual?
Questions and answers
My AR-1733 Is just showing the time and alarm set. None of the other buttons are having any effect
@john Shea Solved by a reset
If your DIGITECH AR-1733 is only showing the time and alarm set, and other buttons are not working, try pressing and holding the PAGE button for 3 seconds while the radio is off to enter or exit alarm setting mode. If the issue persists, use a toothpick to press the reset button located in the reset hole on the bottom of the unit.
This answer is automatically generated
load atc frequencies
To load ATC (Air Traffic Control) frequencies on the DIGITECH Audio AR-1733:
1. Press the "BAND" button to select the AIR band (118 ~ 137 MHz).
2. Press the “FREQ” button.
3. Enter the desired ATC frequency using the 0-9 number keys.
This will tune the radio to the entered ATC frequency in the AIR band.
This answer is automatically generated