Advertisement
Quick Links
Advertisement
Related Manuals for KTM 85 SX 19/16 2013
Summary of Contents for KTM 85 SX 19/16 2013
- Page 1 SETUP INSTRUCTIONS 2013 85 SX 19/16 85 SX 17/14 Art. no. 3211905en...
- Page 3 KTM accepts no liability for delivery options, deviations from illustrations and descriptions, as well as misprints and other errors.
-
Page 4: Means Of Representation
MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Indicates a page reference (more information is provided on the specified page). Indicates information with more details or tips. - Page 5 SETUP Unpacking and setting up the vehicle – Remove the box and the plastic packaging. Info An assistant prevents the motorcycle from falling over. To avoid damaging the motorcycle during the setup, leave the protective film on the vehicle until you have finished. –...
- Page 6 SETUP – Position the handlebar. Info Make sure the cables and wiring are positioned correctly. – Position the handlebar clamps. Mount and tighten the screws evenly. Guideline Screw, handlebar clamp 20 Nm (14.8 lbf ft) 201940-10 Info The markings on the handlebar should be at the center of the handlebar clamps.
- Page 7 Activate the front brake and compress the fork a number of times forcefully to align the fork legs. – Tighten screws Guideline Screw, fork stub 15 Nm (11.1 lbf ft) 201944-10 – Refuel. ( p. 8) – Print out the current PDI form found on KTM DEALER.NET and perform the delivery inspection.
- Page 8 WORK Raising the motorcycle with the lift stand Note Danger of damage The parked vehicle may roll away or fall over. – Always place the vehicle on a firm and even surface. – Raise the motorcycle at the frame underneath the engine. Lift stand (59229055000) The wheels must no longer touch the ground.
- Page 9 WORK – Pull the front wheel brake and push down hard on the fork several times to align the fork legs. – Tighten screws Guideline Screw, fork stub 15 Nm (11.1 lbf ft) Finishing work – Remove the motorcycle from the lift stand. ( p.
- Page 10 WORK – Turn filler cap counterclockwise and lift it off. L00023-10 Closing the filler cap – Mount filler cap and turn it clockwise until the fuel tank is tightly closed. Info Run fuel tank breather hose without kinks. L00023-11 Refueling Danger Fire hazard Fuel is highly flammable.
-
Page 11: Technical Data - Tightening Torques For Chassis
TECHNICAL DATA - TIGHTENING TORQUES FOR CHASSIS – Spoke nipple M4.5 5 Nm (3.7 lbf ft) – Rear brake bolt 12 Nm (8.9 lbf ft) – Remaining nuts, chassis 10 Nm (7.4 lbf ft) – Remaining screws, chassis 10 Nm (7.4 lbf ft) –... - Page 12 SUBSTANCES 2-stroke engine oil According to – JASO FC ( p. 12) Guideline – Only use high quality 2-stroke engine oil of a well-known brand. KTM recommends Motorex ® products. Fully synthetic Supplier Motorex ® – Cross Power 2T Super unleaded (ROZ 98 / RON 98 / PON 94) According to –...
-
Page 13: Auxiliary Substances
AUXILIARY SUBSTANCES Long-life grease Guideline – KTM recommends Motorex ® products. Supplier Motorex ® – Bike Grease 2000... - Page 14 STANDARDS JASO FC JASO FC is a classification for a 2-stroke engine oil that was specifically developed for the extreme demands of racing. Thanks to first rate synthetic esters and specially designed additives, superb combustion is achieved even under extreme operating conditions.
- Page 15 *3211905en* 3211905en 08/2012 KTM-Sportmotorcycle AG 5230 Mattighofen/Austria Photo: Mitterbauer/KTM http://www.ktm.com...