Advertisement
Quick Links
Contents
1
General safety instructions _______________________________ 2
2.
Installation ___________________________________________ 9
3.
Description of the controls ______________________________ 15
4.
Operating instructions __________________________________ 19
5
Cleaning and maintenance ______________________________ 20
6
Troubleshooting _______________________________________ 21
Thank you for choosing one of our products.
You are advised to read this manual carefully; it contains all the
information you need about the right conditions for the proper, safe use
of your dishwasher.
This manual contains only the basic information required to use the
appliance. The complete manual can be obtained from
www.smeg.com/download-manuals
by entering the product code shown on the plate attached to the inner
right hand edge of the dishwasher door.
The manual can be accessed quickly via the QR code using a device
with a QR reader application.
1
Advertisement
Related Manuals for Smeg LSPU8612S
Summary of Contents for Smeg LSPU8612S
-
Page 1: Table Of Contents
This manual contains only the basic information required to use the appliance. The complete manual can be obtained from www.smeg.com/download-manuals by entering the product code shown on the plate attached to the inner right hand edge of the dishwasher door. -
Page 2: General Safety Instructions
Warnings TRANSLATION ORIGINAL INSTRUCTIONS 1 General safety instructions This manual is an integral part of the appliance; it must always be kept intact together with the dishwasher for future reference (even if sold). Before using appliance, carefully read instructions contained in this manual. ... - Page 3 Warnings The installation and repair or servicing shall be carried out by qualified and authorised technical personnel. Interventions by unauthorised personnel can be dangerous and cause the warranty to lapse. The installation must comply with all the directives of the country where the dishwasher is installed, and in the absence of them, in the United States the National Electric Code;...
- Page 4 Warnings If the appliance is installed in a compartment above or below another equipment (e.g. gas burners, ovens, etc.), read carefully the instructions provided by the manufacturer of the equipment. If the instructions of the equipment do not contain information, contact the manufacturer of the equipment to ensure that the appliance can be installed above or below it.
- Page 5 Warnings The plug of the appliance must be accessible after installation. Never disconnect the plug by pulling on the power supply lead. If the appliance is provided with a plugless supply cord, an omnipolar circuit breaker providing a full disconnection in overvoltage protection class III must be installed in an easily accessible position on the supply lineile.
- Page 6 Warnings distributor is empty after completion of the wash cycle. Cleaning and regular maintenance of the appliance by children is only permitted under the supervision of a person responsible for their safety. Some detergents are strongly alkaline. Avoid contact with the skin and eyes.
- Page 7 Warnings The appliance satisfies all applicable safety regulations governing electrical equipment. Any technical checks should be conducted exclusively by trained authorised technicians: repairs performed by unauthorised persons not only void the warranty but may also put the user’s safety at risk. ...
- Page 8 Warnings Warning: The device only works dishwasher is connected to the mains. 1.1 Disposal The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current European directives: To dispose of the appliance: ...
-
Page 9: Installation
Installation 2. Installation 2.1 Technical characteristics Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) Water supply temperature max. 60°C-140°F Capacity 12-13 standard place settings Class of protection against IPX0 moisture Protection against electric class I shock Electrical data... - Page 10 Installation General Information This appliance6 may be placed up against walls or other furniture units. If the appliance is installed near a heat source, fit a special insulating panel to prevent overheating and malfunction of the appliance. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction;...
- Page 11 Installation Building-in a dishwasher underneath a hob is absolutely forbidden. Moreover, dishwashers may not be installed directly touching appliances which are not conventional built-in kitchen appliances (e.g. fireplaces, stoves, etc.). When installing the dishwasher in a compartment next to one or more other appliances, it is essential to comply with all the recommendations provided appliance’s manufacturer...
- Page 12 Installation Water supply connection CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾” gas thread, inserting the filter A supplied with the dishwasher. Take care to screw the hose firmly into place with your hands and then complete by tightening about ¼...
- Page 13 Installation DRAIN CONNECTION Insert the dishwasher’s drain hose into a drain pipe having a diameter of at least 4 cm (1"37/64), or alternatively, place it inside the kitchen sink using the plastic support provided, taking care not to crush or excessively bend the hose.
- Page 14 Installation 2.4 Electrical connection Check that the voltage and the frequency of the mains match the ratings on the name plate of the appliance positioned on the inner edge of the door. The plug on the supply cord and the corresponding socket outlet must be of the same type and meet the regulations in force.
-
Page 15: Description Of The Controls
Installation 3. Description of the controls 3.1 Front panel All the dishwasher controls are grouped on the front panel. Programming and option selection are only possible with the door closed. ON/OFF BUTTON AND WARNING LIGHT SANITATION INDICATOR LIGHT NO RINSE AID LIGHT PROGRAM SELECTION BUTTON START/PAUSE BUTTON PROGRAM INDICATOR LIGHTS... - Page 16 User instructions PROGRAM SELECTION Press the PROGRAM SELECTION button (4) several times until the light of the program required comes on. STARTING THE PROGRAM To start the dishwasher, press the START/PAUSE button (5) for a few seconds, until the light of the selected program starts to flash (confirmation beep).
- Page 17 Installation PROGRAMS TABLE Program 65°C 70°C ● HALF ● 1,20 (146°F) (158°F) (3,43 gal) LOAD P2 (2) 45°C 64°C 15,5 ● 1,20 NORMAL (113°F) (147°F) (4,1 gal) 19.3l 50°C 70°C cold 2 cold ● 1,15 DELICATE (122°F) (158°F) (5,1 gal) 65°C 70°C 13,5...
- Page 18 User instructions 1 – The cycle times and electrical energy listed use and care manual are based on normal soil loads and 120°F (49°C) incoming water and will vary based on your actual conditions. 2 – Program for energy star. Only “POTS &...
-
Page 19: Operating Instructions
Installation 4. Operating instructions After having installed the dishwasher, remove the basket retainers. 4.1 Adding the salt The salt prevents the formation of scale deposits. Unscrew the cap of the salt container. Only for the first time, fill the container with a litre of water. -
Page 20: Cleaning And Maintenance
User instructions 5 Cleaning and maintenance Before carrying out any work, always unplug the appliance from the electrical supply or switch off the omnipolar circuit breaker. CLEANING THE WATER INTAKE FILTER Close the water supply tap, unscrew the end of the water intake hose, remove the filter A and clean it under running water. -
Page 21: Troubleshooting
Installation 6. Troubleshooting The dishwasher is capable of signalling a number of faults through the simultaneous illumination of several indicator lights, with the following meanings: FAULT DESCRIPTION Acquastop failure The anti-flooding system has been activated (for the relevant models only). The system is tripped in case of water leaks. - Page 22 User instructions FAULT DESCRIPTION Turbine flow-regulator malfunction (for the relevant models only) The appliance is not able to "measure" the amount of water loaded accurately. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle.