Remote Control - Hegel H120 User Manual

Remote Control - RC8
COMPUTER
PREV PLAY NEXT
DAC+
ECO DISP
PREV
PLAY NEXT
IN+ STOP VOL+
IN- MUTE VOL-
12
Remote control buttons (starting top left)
1. PREV Skip to previous track on most media players
2. PLAY Play/Pause on most media players
3. NEXT Skip to next track on most media players
4. DAC+ Input source selector button for Hegel DACs
5. ECO On/Off (standby)
6. DISP Display on/off (hold for off)
7. PREV Skip to previous track on Hegel CD-players
8. PLAY Play/Pause for Hegel CD-players
9. NEXT Skip to next track on Hegel CD-players
10. IN+
Switches to next input on Hegel amplifiers
11. STOP Stop/Eject for Hegel CD-players
12. VOL+ Volume up for Hegel amplifiers
13. IN-
Switches to previous input on Hegel amplifiers
14. MUTE Mute for Hegel amplifiers
15. VOL- Volume down for Hegel amplifiers
General information
The Hegel amplifier can be controlled with
the included Hegel RC8 Remote Control.
The RC8 controls Hegel products, such as
amplifiers and preamplifiers, and most me-
dia players, avoiding the need for multiple
remote controls
The remote control uses two standard 1.5-
volt LR03 AAA batteries. To insert the bat-
teries, use a crosshead (Phillips) screw-
driver to gently remove the four screws on
the underside of the remote control.
Insert the batteries with the correct polarity
with + sign and – sign, as shown inside the
battery holder. Be careful when inserting the
batteries to not damage the battery holder.
Replace the cover. Insert the screws by gen-
tly turning them by hand, to avoid damaging
the threads in the remote control chassis.
Do not tighten the screws too much, as this
can damage the screws and the soft metal
chassis of the remote control.
CAUTION: Do not drop the remote control
on the floor, as this can damage its internal
parts and the battery holder.
Mute
The MUTE(14) button mutes the outputs on
the amplifier. The volume flashes to
indicate that mute is on. Press the mute
button, or adjust the volume level, to switch
mute off.
On/Off (standby)
The ECO(5) button will turn the amplifier on
or off (standby).
Display On/Off
The DISP(6) button may be used to turn
the display on or off. Hold the DISP button
for more than 1 second to turn the display
off. When adjusting inputs or volume the
display will light up momentarily. To turn the
display on again, press DISP.
Set max startup volume
When powering on the amplifier, the volume
will automatically be set to the same level as
when the amplifier was switched off. To pre-
vent the amplifier from powering up at an
unwanted volume level, it is possible to set a
user defined max startup volume. Adjust the
volume to the desired max startup volume.
Press DAC+(4) and VOL-(15) simultane-
ously. The volume indicator will blink three
times and the the new max startup volume
has been saved.
Set max volume level
A user defined volume level may be used
as the amplifier's maximum output volume.
Adjust the volume to the desired maximum
level (e.g., volume 59). Press DAC+(4) and
VOL+(12) simultaneously. The volume
indicator will change to "100 Damped". The
volume level on volume 100 is now damped
to yor chosen setting (e.g., volume 59). To
reset to the default max volume level, turn
the volume all the way up to "100 Damped"
and press DAC+ and VOL+. The volume
indicator will change back to the level that
was set as the max volume (e.g., volume
59). The max volume has been reset to
default.
Reset to Factory Default Settings
By pressing and holding the DAC+(4) button
while pressing MUTE(14), the amplifier will
be reset to factory settings. This can also be
done from the device menu.
13