Sony HCD-XGV6 Service Manual page 2

HCD-XGV6/XGV8/XGV10AV
Outputs
PHONES:
(stereo phone jack) accepts headphones of 8 ohms or more
MD (VIDEO) OUT:
(phono jacks) voltage 250 mV
impedance 1 kilohms
LBT-XGV10AV
WOOFER OUT (phono jack): voltage 1 V, impedance 1 kilohm
FRONT SPEAKER: accepts impedance of 6 to 16 ohms
CENTER SPEAKER: accepts impedance of 8 to 16 ohms
REAR SPEAKER: accepts impedance of 8 to 16 ohms
LBT-XGV8
FRONT SPEAKER: accepts impedance of 6 to 16 ohms
(SUPER WOOFER)
accepts impedance of 6 to 16 ohms
(TWEETER & WOOFER)
LBT-XGV6
FRONT SPEAKER: accepts impedance of 6 to 16 ohms
Video section
Inputs
GAME INPUT (phono jack): 1 V p-p, 75 ohms
Outputs
VIDEO OUT (phono jack): 1 V p-p, 75 ohms
VIDEO CD/CD player section
System Compact disc and digital audio system
Laser Semiconductor laser
(λ=795nm), Emission
duration: continuous
Frequency response 2 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio More than 90 dB
Dynamic range More than 90 dB
Video color system format NTSC, PAL
Tape player section
Recording system 4-track 2-channel stereo
Frequency response 40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
Wow and flutter ±0.15% W.Peak (IEC)
0.1% W.RMS (NAB)
±0.2% W.Peak (DIN)
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 – 108.0 MHz
(50 kHz step)
Antenna FM lead antenna
Antenna terminals 75 ohms unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
Middle Eastern model: 531 – 1,602 kHz
(with the interval set at 9 kHz)
Other models: 531 – 1,602 kHz
(with the interval set at 9 kHz)
530 – 1,710 kHz
(with the interval set at 10 kHz)
Antenna AM loop antenna
Antenna terminals External antenna terminal
Intermediate frequency 450 kHz
General
Power requirements
Saudi Arabian model: 120 – 127 V, 220 V or 230 – 240 V AC,
50/60 Hz
Adjustable with voltage selector
2
All manuals and user guides at all-guides.com
Thai model:
Other models:
Power consumption
LBT-XGV10AV
LBT-XGV8
LBT-XGV6
Dimensions (w/h/d)
Mass:
LBT-XGV10AV
LBT-XGV8
LBT-XGV6
Supplied accessories:
Design and specifications are subject to change witho fi notice.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
220 V AC, 50/60 Hz
120 V, 220 V or 230 –240 V AC,
50/60 Hz
Adjustable with voltage selector
230 watts
320 watts
180 watts
Approx. 355 x 425 x 451 mm
Approx. 15.4 kg
Approx. 16.4 kg
Approx. 14.7 kg
AM loop antenna (1)
FM lead antenna (1)
Speaker cords (XGV6, XGV8 (4),
XGV10AV (5))
Speaker pads (XGV6, XGV8 (8),
XGV10AV (12))
Remote commander (1)
Batteries (2)
Video connecting cable (1)