Table of Contents
Advertisement
Introduction for buttons on
remote controller
NOTE
●
This is a general use remote controller . It could be
used for the air conditioner with multifunction. For the
functions which the model doesn't have, if press the
corresponding button on the remote controller , the
unit will keep the original running status.
●
After putting through the power, the air conditioner
will give out a sound. Power indicator "
After that, you can operate the air conditioner by
using remote controller.
●
Under on status, pressing the button on the remote
controller, the signal icon "
remote controller will blink once and the air condition-
er will give out a sound, which means the signal has
been sent to the air conditioner.
button
Press this button to turn on the unit. Press this button
again to turn off the unit.
MODE button
Press this button to select your required operation
mode.
AUTO
COOL
●
When selecting auto mode, air conditioner will
operate automatically according to ambient tem-
perature. Set temperature can't be adjusted and
will not be displayed as well. Press "FAN" button
can adjust fan speed.
●
When selecting cool mode, air conditioner will
operate under cool mode. Press "+" or "-"
button to adjust set temperature. Press "FAN"
button to adjust fan speed.
●
When selecting dry mode, the air conditioner
operates at low speed under dry mode. Under
dry mode, fan speed can't be adjusted.
●
When selecting fan mode, the air conditioner will
only blow fan, no cooling and no heating. Press
"FAN" button to adjust fan speed.
●
When selecting heat mode, the air conditioner
operates under heat mode. Press "+" or "-"
button to adjust set temperature. Press "FAN"
button to adjust fan speed.
" is ON.
" on the display of
HEAT
DRY
FAN
NOTE
●
For preventing cold air, after starting up heat mode,
indoor unit will delay 1~5 minutes to blow air (Actual
delay time depends on indoor ambient temperature).
●
Set temperature range from remote cont rolle r:
16~30℃(61-86℉).
●
This mode indicator is not available for some models.
●
Cooling only unit won't receive heat mode signal. If
setting heat mode with remote cont roller, press
"
" button can't start up the unit.
FAN button
This button is used for setting Fan Speed in the
sequence that goes from AUTO,
to
, then back to Auto.
NOTE
●
Fan Speed "
Fan Speed "
for some models.
●
Under AUTO speed, air conditioner will select proper
fan speed automatically according to factory default
setting.
●
AUTO speed is only available for some models.
'
●
It
s low fan speed under dry mode.
●
X-FAN function: Holding fan speed button for 2s in
cool or dry mode, the icon
indoor fan will continue operation for a few minutes in
order to dry the indoor unit even though you have
turned off the unit. After energization, X-FAN OFF is
defaulted. X-FAN is not available in auto, fan or heat
mode.
This function indicates that moisture on evaporator of
indoor unit will be blowed after the unit i s stopped to
avoid mould.
●
Having set X-FAN function on : After turning off the
unit by pressing "
running for a few minutes at low speed. In this period,
hold fan speed button for 2s to stop indoor fan directly.
Having set X-FAN function off: After turning off the
unit by pressing "
be off directly.
●
X-FAN function is only available for some models.
- / + button
Press "+" or "-" button once increase or decrease
set temperature 1℃(℉). Holding "+" or "-" button, 2s
later, set temperature on remote controller will
change quickly. On releasing button after setting is
finished, temperature indicator on indoor unit will
change accordingly. (Temperature can' t be adjust-
ed under auto mode)
When setting TIMER ON, TIMER OFF or CLOCK,
press "+" or "-" button to adjust time. (Refer to
CLOCK, TIMER ON, TIMER OFF functions).
- 6 -
,
" is unavailable for some models,
" is the same with Fan Speed "
"
"
is displayed and the
" button, indoor fan will continue
" button, the complete unit will
,
,
"
Advertisement
Table of Contents
