Mercia Garden Products 01OVLPA0510PB-V1 Assembly Instructions

01OVLPA0510PB-V1 01OSBA510PB-V1 01SHPA0510PB-V1

Before assembly

please make sure you have a
suitable base ready to erect your
building
01OSBA0510PB-V1
MADE IN GREAT BRITAIN
01SHPA0510PB-V1
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be a ected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be
slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also
recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71
level, we cannot accept responsibility for your safety whilst erecting or using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
01OVLPA0510PB-V1
Overall Dimensions:
Length = 1502mm
Width = 2259mm
Height = 3094mm
Base Dimensions:
Length = 1487mm
Width = 3094mm
x2
This building should be erected by
two adults
For ease of assembly, you must pilot
drill all screw holes and ensure all
screw heads are countersunk.
2mm Drill bit
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every e ort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
For Assistance Please
Contact Customer Care on
01636 880514
Please retain product label and instructions for future reference
Building content for:
01OVLPA0510PB-V1 & 01OSBA0510PB-V1
Plain Side Window Side
Truss
Ridge Bar - 1486mm Qty 2
Truss Block - 140mm Qty 2
Felt
Plastic Window Cill
Building content for:
01SHPA0510PB-V1
(Check building label for product code)
Plain Side Window Side
Truss
Ridge Bar - 1486mm Qty 2
Truss Block - 140mm Qty 2
Felt
Casement Stay
(Check building label for product code)
Floor Roof Sheet
Qty 2 Qty 2
Cover Trim - 1575mm Qty 2
Window Strip - 546mm Qty 5
Floor Blocks - 400mm Qty 8
Eaves Frame - 1502mm Qty 2
Styrene
Qty 2
Floor Middle Roof
Qty 2 Qty 2
Cover Trim - 1575mm Qty 2
Opening Window Strip - 1155mm Qty 1
Floor Blocks - 400mm Qty 8
Eaves Frame - 1502mm Qty 2
Opening Window
Butt Hinge
Qty 2
Qty 2