Rinse Aid And Refined Salt; Measuring Out The Rinse Aid; Measuring Out The Refined Salt - Hotpoint Ariston ELTB 6M124 Manual

Rinse aid and refined salt

Only use products which have been specifically designed
EN
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
(Follow the instructions given on the packaging).
very hard.
If you do not add salt or rinse aid, the LOW SALT
LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
is illuminated, a reserve supply of rinse aid is still available
on the lid;
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Rinse-aid dispenser setting
If you are not completely satisfied with the drying results, you
Press the P
the indicator light of the set level flashes
Adjust the level of rinse aid supply using the P button; during
this procedure the rinse aid indicator light flashes.
Press the ON/OFF button to save the setting.
you run out of rinse aid.
Up to maximum 4 levels can be set based on the dishwasher
model.
adjustment device to a higher number (3-4.)
Setting the water hardness
using refined salt specially designed for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
24
*
on the control panel
"D"
by pressing and pulling up the tab
(the default rinse-aid
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
and hold the P button for a few seconds until you hear a beep
indicator light of the set level flashes
During this procedure the salt indicator light flashes.
*
Adjust the hardness level using the P button,
and
water hardness table)
Press the ON/OFF button to save the setting.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
Water Hardness Table
level ° dH
1 0 - 6
2 6 - 11
3 12 - 17
4 17 - 34
*
34 - 50
5
For values between 0°f and 10°f, we do not recommend the use of salt.
*
a setting of 5 may increase cycle duration.
**
1 wash cycle per day.

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refined salt removes limescale from the water, thus avoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
the cap of the salt dispenser;
*
is illuminated
water to leak out.
4. Remove the funnel* and wipe any salt residues away from
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
so that any saline solution which has leaked out of the salt
dispenser is removed.
*
Only available in selected models.
(the default setting of the
*
up to max. 5 levels.
Average salt dispenser
capacity duration
° fH mmol/l months
0 - 10 0 - 1 7 months
11 - 20 1,1 - 2 5 months
21 - 30 2,1 - 3 3 months
31 - 60 3,1 - 6
2 months
61 - 90 6,1 - 9 2/3 weeks
*
cannot be seen by simply looking at
;
cap (anticlockwise).
tank right up to its edge.
*
(see figure)
3. Position the funnel
fill the salt dispenser up to the edge
*
).
*
see
**
and