Ebsray V Series Installation, Operation & Maintenance Instructions Manual
Rotary sliding vane pumps
Hide thumbs
Also See for V Series:
Related Manuals for Ebsray V Series
Summary of Contents for Ebsray V Series
- Page 1 Publication # 2301-08 EBSRAY PUMPS INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS V2000 V3000 V3010 V SERIES MODELS V2000, V3000 & V3010 ROTARY SLIDING VANE PUMPS...
-
Page 2: Table Of Contents
State and Local Directives, Standards, Codes and Regulations. Ebsray reserves the right to: a) Withdraw or alter any or all of the Ebsray specifications within this Publication and any other relevant Ebsray documents without notification. b) Determine the validity of any Warranty claims for Ebsray equipment based on the proper application of Ebsray supplied equipment by the way of adherence to the Ebsray specifications within this Publication and any other relevant Ebsray documents. -
Page 3: Section 1 - General
Ebsray pumps make them capable of advise Ebsray or their Appointed Representative. reliable operation over a long working life. Correct Should a shortage be evident on receipt, notify Ebsray installation and operation is essential. Service life is immediately giving full details and packing note number. -
Page 4: Section 2 - Installation
The pumping unit should be placed as close as practicable If pump was supplied by Ebsray as part of a pumpset unit, to the source of supply keeping within the NPSHr of the pump and driver have been accurately aligned at factory. -
Page 5: Section 3 - Operation
SECTION 3 – OPERATION PRE-STARTUP CHECKLIST D ESCRIPTION Do not run Pump dry. Do not The EBSRAY Models V2000, V3000 & V3010 are positive WARNING start Pump against closed displacement Sliding Vane Pumps, primarily intended for the Discharge Valve unless external bypass protection is transfer of LPG and other low to medium viscosity liquids. -
Page 6: 4.2.2 Pump
– are used. excessive wear is evident, it is recommended to replace both components. Sco ring in the seal zones of the liner is Only use genuine Ebsray spare pa rts. rimental to opt u m performance. NB: The rotor is perman ntly attached to the shaft. -
Page 7: Reassembly
REASSEMBLY Lockwashers must WARNING reused as bending the tabs (Refer Section 5 – Parts Designation) an once may cause fatig ue wh ould more th ich c result in Pump Fastener Torque settings: V2000 V3000/V3010 V3010 failure and/or major p ump da mage. -
Page 8: Section 5 - Parts Designation
SECTION 5 – PARTS DESIGNATION MODELS: V2000, V300 and V3010 Rotary Sliding Vane p ump. Cat# Description Cat# Description Body Valve Seat (for aluminium body only) Liner Spring - Bypass Valve Rotor/Shaft assembly Spring Cap Wearplate Mechanical Seal Assembly Vane Oil Seal Vane Pushrod O-Ring - Body Cover... -
Page 10: Section 6 - Troubleshooting
SECTION 6 – TROUBLESHOOTING Possible Symptom Possible Cause Remedy Problem Pump not operating No power to drive shaft Check driver No Liquid Coupling damaged or disengaged Repair/replace coupling Delivery Pump will not turn – Foreign matter in pump Clean out pump – check strainer in locked up suction line. -
Page 11: Appendix A - Declaration Of Conformity
Manufacturer 628 Pittwater Road Brookvale NSW 2100 Australia Address Manufacturer’s Declaration We, Ebsray Pumps Pty Ltd declare that the following equip ment : Description of Equipment Ebsray V Series Sliding Vane bareshaft Pump ; Model / Type : (all Types) except Liquefied Gases... - Page 12 NOTES...
Need help?
Do you have a question about the V Series and is the answer not in the manual?
Questions and answers