Related Manuals for Ebsray RC40
Summary of Contents for Ebsray RC40
- Page 1 Publication # 1987-16EN EBSRAY PUMPS INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS RC SERIES MODELS RC20, RC25 & RC40...
-
Page 2: Table Of Contents
WARRANTY ............................4 SECTION 2 – SYSTEM DESCRIPTION ........................5 EBSRAY RC20/RC25/RC40 LPG PUMPING SYSTEM ................ 5 BYPASS VALVE – EBSRAY MODEL RV18 (VRS OR CBS OPTIONS) ..........5 SECTION 3 – INSTALLATION ............................. 5 PUMP & SYSTEM LOCATION/INSTALLATION ................... 5 3.1.1... - Page 3 CE conformity. For U.L Models, the “3” in the last digit of in the Ebsray RC20/RC25 Model No. Code on the Nameplate indicates that this product is listed by UL for LP-Gas Applications Only. For example, in the Ebsray Model No. Code RC25NN-1BF1-A1N3, the “3”...
-
Page 4: Section 1 - General
Refer to change be contemplated, please confer with Ebsray Pumps 'Standard Conditions of Sale and Ebsray in order to verify the suitability of such a Warranty' publication for details. change 2. Ancillary equipment supplied by Ebsray but... -
Page 5: Section 2 - System Description
Ebsray. 2.2 BYPASS VALVE – EBSRAY MODEL RV18 (VRS OR CBS OPTIONS) The RC Series Pumps must be installed in conjunction with a bypass valve - connected back-to-tank. The EBSRAY Model RV18 fitted with VRS or CBS option is recommended. -
Page 6: Bypass Valve
AND BYPASS ADJUSTMENT 1. Pump Fill in the ‘Pump Run Log’ provided in Appendix C The Ebsray RC Series pumps are designed for ultra quiet operation pumping LPG of Internationally 1. Ensure all conditions described in Pre-Start-Up accepted (ISO) quality and specification. -
Page 7: Periodic Inspection
Ancillary Equipment is required to maintain safety, conformity, operational functionality and reliability. 12. While retaining the Adjustment Screw, lock the Ebsray recommends a maximum interval of three Adjusting Screw Lock Nut against Bypass Valve months or 500 hours operation between routine Cover immediately after adjustment is made. -
Page 8: Section 5 - Maintenance
Cartridge. Ref Fig 2 Fig 3 Complete Quill Assembly Insert grubscrews Complete Quill Assemblies are into NOTE: available from EBSRAY as a 'Spare extraction holes and Part' enhance speed efficiency screw in evenly to maintenance. extract Cartridge or Quill Assembly. -
Page 9: Inspection
Remove Circlip 5.6 SPARE PARTS from end of Quill 1. When ordering spare parts, to ensure a minimum Assembly. of delay and correct replacement to original Refer Fig 4 specification, ALWAYS quote the pump Serial Number located on the nameplate of the pump. 2. - Page 10 Final pump assembly c) Press Seal Seat in with fingers. (Ensure complete 7. Fit Dust Seal to Body. and square (Note position of lip) engagement) Refer Fig 15 Refer Fig 9 Fig 9 Fig 15 8. To assist assembly, 3. Fit Primary O-Ring lightly lubricate bore in to Cartridge then fit cartridge zone with a...
-
Page 11: Section 6 - Parts Designation
SECTION 6 – PARTS DESIGNATION PARTS DESIGNATION - EBSRAY MODELS: RC20, RC25 and RC40 (Refer Drawing N A316001L and A319001L) Description Description Body Coupling Guard Cover Setscrew -Coupling Guard Impeller Plug - Spare Port O-Ring – Cover Seal Drain Elbow...
Need help?
Do you have a question about the RC40 and is the answer not in the manual?
Questions and answers