Ebsray V Series Installation, Operation & Maintenance Instructions Manual
Rotary sliding vane pumps
Hide thumbs
Also See for V Series:
Related Manuals for Ebsray V Series
Summary of Contents for Ebsray V Series
- Page 1 Publication # 2302-13 EBSRAY PUMPS INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS V2000 V3000 V3010 V SERIES MODELS V2000, V3000 & V3010 ROTARY SLIDING VANE PUMPS...
-
Page 2: Table Of Contents
State and Local Directives, Standards, Codes and Regulations. Ebsray reserves the right to: a) Withdraw or alter any or all of the Ebsray specifications within this Publication and any other relevant Ebsray documents without notification. b) Determine the validity of any Warranty claims for Ebsray equipment based on the proper application of Ebsray supplied equipment by the way of adherence to the Ebsray specifications within this Publication and any other relevant Ebsray documents. -
Page 3: Section 1 - General
Ebsray pumps make them capable of advise Ebsray or their Appointed Representative. reliable operation over a long working life. Correct Should a shortage be evident on receipt, notify Ebsray installation and operation is essential. Service life is immediately giving full details and packing note number. -
Page 4: Section 2 - Installation
The pumping unit should be placed as close as practicable If pump was supplied by Ebsray as part of a pumpset unit, to the source of supply keeping within the NPSHr of the pump and driver have been accurately aligned at factory. -
Page 5: Section 3 - Operation
500 pump immediately and take action to rectify the problem. hours of operation. Ebsray recommends the use of a lithium complex NLGI Grade 2 grease with an ISO VG220 viscosity For safe operation, the following items should be included in the routine periodic inspection: rating. -
Page 6: Pump
Bearings, etc – are used. excessive wear is evident, it is recommended to replace both components. Scoring in the seal zones of the liner is Only use genuine Ebsray spare parts. detrimental to optimum performance. NB: The rotor is permanently attached to the shaft. -
Page 7: Reassembly
REASSEMBLY Lockwashers must WARNING reused as bending the tabs (Refer Section 5 – Parts Designation) more than once may cause fatigue which could result in failure and/or major pump damage. Only reassemble Pump Fastener Torque settings: V2000 V3000/V3010 V3010 Body Material with new lockwashers of the correct thickness (Refer Body Cover to Body 77Nm... -
Page 8: Section 5 - Parts Designation
SECTION 5 – PARTS DESIGNATION MODELS: V2000, V3000 and V3010 Rotary Sliding Vane pump. Cat# Description Cat# Description Body Valve Seat (for aluminium body only) Liner Spring - Bypass Valve Rotor/Shaft assembly Spring Cap Wearplate Mechanical Seal Assembly Vane Oil Seal Vane Pushrod O-Ring - Body Cover 116/117... -
Page 10: Section 6 - Troubleshooting
SECTION 6 – TROUBLESHOOTING Possible Symptom Possible Cause Remedy Problem Pump not operating No power to drive shaft Check driver No Liquid Coupling damaged or disengaged Repair/replace coupling Delivery Pump will not turn – Clean out pump – check strainer in Foreign matter in pump locked up suction line. -
Page 11: Appendix A - Declaration Of Conformity
Manufacturer 628 Pittwater Road Brookvale NSW 2100 Australia Address Manufacturer’s Declaration We, Ebsray Pumps Pty Ltd declare that the following equipment : Description of Equipment Ebsray V Series Sliding Vane bareshaft Pump ; Model / Type : (all Types) except Liquefied Gases... - Page 12 NOTES...
Need help?
Do you have a question about the V Series and is the answer not in the manual?
Questions and answers