Page 2
The information in this document has been carefully checked and is believed to be entirely reliable. esd makes no warranty of any kind with regard to the material in this document, and assumes no responsibility for any errors that may appear in this document. In particular descriptions and technical data specified in this document may not be constituted to be guaranteed product features in any legal sense.
Page 3
New Declaration of Conformity inserted Order information revised Chapter 2.”Quick Start” deleted Safety Instructions revised , Classification inserted Description of DN-DP revised Technical details are subject to change without further notice. DN-DP Page 3 of 21 Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
Page 4
Caution statements indicate a hazardous situation that, if not avoided, could result in minor or moderate injury. INFORMATION INFORMATION Notes to point out something important or useful. Page 4 of 21 DN-DP Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
Page 5
¡ around the DN-DP module and use care when handling. Do not operate the DN-DP module adjacent to heat sources and do not expose it to unnecessary ¡ thermal radiation. Ensure an ambient temperature as specified in the technical data.
Page 6
The operation of the DN-DP for medical purposes is prohibited. Service Note The DN-DP does not contain any parts that require maintenance by the user. The DN-DP does not require any manual configuration of the hardware. Unauthorized intervention in the device voids warranty claims.
The DN-DP gateway operates as a PROFIBUS DP slave-I/O component. At the DeviceNet network the DN-DP gateway can operate as a scanner to control several DeviceNet slave devices or as a single slave device to be connected to one DeviceNet scanner.
Page 9
The PROFIBUS DP as well as the DeviceNet interface are electrically isolated. The module can be configured via a PROFIBUS configuration tool, e.g. the PLC SIMATIC Manager or the TIA Portal. DN-DP Page 9 of 21 Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
Hardware Installation 2. Hardware Installation 2.1 Connecting Diagram Fig. 2: Connections of the DN-DP module INFORMATION The connector pin assignment can be found on page 15 and following. For conductor connection and conductor cross section see page 18. Page 10 of 21 DN-DP Hardware Manual •...
The complex indication function of the LEDs is controlled by the firmware. After connecting the power supply voltage, initially all LEDs will be off until the firmware has booted. DN-DP Page 11 of 21 Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
Changes of the settings have to be made before switching on the module because changes during operation have no effect. The DN-DP is operated as slave station with a configurable decimal address range from 1 to 126 or hexadecimal from 01 to 7E Configuring an address lower than 1, the address 1 is valid.
8M x 32 Bit (32 MB) Memory Flash-EPROM: 512 K x 16 Bit (1 MB) Serial EEPROM Debug interface for service and programming (for internal use only) Table 3: PowerPC Unit DN-DP Page 13 of 21 Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
Signal description: V+... power supply voltage (U = 24 V) V-... reference potential to V+ , CAN_L and CAN_H CAN_L, CAN_H ... CAN signal lines PE_GND ... shield DN-DP Page 15 of 21 Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
For conductor connection and conductor cross section see page 18. Pin position: Pin Assignment: Signal +24 V Signal description: +24 V... power supply voltage GND ... reference potential - ... not connected DN-DP Page 17 of 21 Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
2 conductors with same cross section, stranded, 1 mm² 1.5 mm² TWIN ferrules with plastic sleeve, max. Minimum AWG according to UL/CUL Maximum AWG according to UL/CUL n.a..not allowed Page 18 of 21 DN-DP Hardware Manual • Doc.-No.: C.2930.21 / Rev. 1.5...
Table 6: Order information PDF Manuals Manuals are available in English and usually in German as well. For availability of English manuals see the following table. Please download the manuals as PDF documents from our esd website www.esd.eu for free. Manuals Order No.
Need help?
Do you have a question about the DN-DP and is the answer not in the manual?
Questions and answers