Eachine US65 Quick Start Manual

Features
24gram 1-2s brushless 65mm whoop
New AIO 4in1 CrazybeeX flight controller
Smooth and powerful
CADDX ANT Camera
High performance 2.0 plug
Specifications
Brand Name: Eachine
Item Name: US65 PRO/DE65 PRO
Wheelbase: 65mm
Size: 81mmx81mmx39mm
Weight: 24g(without battery)
Receiver option
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
External Frsky RXSR receiver version(ACCST D16 sbus output)
External TBS Crossfire Nano receiver version
Package includes
Item Name
US65 PRO or DE65 PRO Frame and canopy
Option1: CrazybeeX FR V1.0 built-in internal Frsky SPI D8/D16 receiver
Option2: CrazybeeX FS V1.0 built-in internal Flysky SPI receiver
Option3:CrazybeeX PNP V1.0 with External Frsky RXSR receiver
Option4:CrazybeeX PNP V1.0 with External TBS crossfire nano receiver
Eachine NX0802 KV14000 brushless motor
Gemfan 1219-3 Propellers(4cw+4ccw)
Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera
5.8G 25mw 40ch vtx (Flight controller built-in)
1S 250mah 30C LiHV Battery
Multi port LIPO/LIHV Battery Charger with 12V adapter
Screw Driver
Propeller disassemble tool
Eachine Handbag
Flight controller connection diagram
BAT+
3.5V-8.7V
GND
+5V
M1
BOOT
LED_STRIP
TX2
RX2
M3
Receiver configuration
1. Connect CH1(TX) of the XF Nano receiver to RX1 pad of the CrazybeeX , Connect CH2(RX) of the
XF Nano receiver to TX1 pad of the CrazybeeX. Enable Serial RX for Uart1 and Smart audio for
UART2
2. Choose the receiver mode to Serial-Based receiver and the Serial Receiver Provider is CRSF.
Enable telemetry in the Betaflight configurator and set AUX8 for RSSI
GND
IR1
M2
M1
BOOT
BUZ-
RX2
LED_STRIP
M2
GND
+5V
TX1
RX1
M4
Eachine US65/DE65 PRO 1-2S 65mm Brushless FPV whoop Tbs crsf version
TBS Micro TX configuration
Some TBS TX and RX setting screen shot
Qty
1
TBS CRSF NANO Bind and Setup video
1
Binding procedure
1
Binding the transmitter and receiver is super simple.
1
1. Just power up the TBS CROSSFIRE transmitter
1 2. On the standard transmitter, enter the configuration menu by pressing and holding the
joystick for 3 seconds, select "General" and "Binding" - a message "Binding" will start
1
blinking, waiting for the receiver. On the micro transmitter, a short press on the button will
4
initiate binding mode.
1
3. Now, power up the receiver (without pressing the Bind button!), if your receiver has not been
1
previously bound, it will automatically bind. Otherwise, press and release the "BIND" button
on the receiver to initiate binding. On the receiver is a timeout of one minute for after power up
1
to enter bind mode. If the status LED will start blinking slowly the receiver has switched
1
successfully to bind mode.
4. Within a few seconds the process will finish with a "Binding complete" message on the
standard transmitter, or a solid green LED on the micro transmitter. The receiver has now stored
the unique serial number of that particular CROSSFIRE transmitter. If it doesn't bind, please
verify that your firmware is to the newest version on both the receiver and the transmitter.
+5V
TX1
Arm/Disarm the Motor Use frsky x9d as an example
RX1
M4
1. The Default Arm/Disarm switch for Us65 PRO/DE65 PRO is AUX1(Channel 5),and you can also
customize it with Betaflight Configurator.
M3
TX2
2.Turn on the transmitter radio which with TBS Micro TX module(Use Frsky x9d as a example) and
move to the MIXER interface, Set "SA" or "SB" switch etc. for Ch5 to ARM/DISARM the motor.
3.The default channel map for US65 PRO/DE65 PRO Crossfire version is TAER1234, please make
sure your transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And also you
can found "Armed" displayed on your FPV Goggles or the FPV Monitor. Please make sure keep the
US65 PRO/DE65 PRO level before arming .Be careful and enjoy your flight now !
https://www.youtube.com/watch?v=ioDzyV2vGb0
Toggle the AUX1 Switch, the Green LED on Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid the Flight controller will getting to be solid