Renesas RTE0T00020KCAA0000J User Manual
Renesas RTE0T00020KCAA0000J User Manual

Renesas RTE0T00020KCAA0000J User Manual

Isolator for the e2 emulator (e2 emulator lite) of ra/re

Advertisement

Quick Links

RTE0T00020KCAA0000J
Isolator for the E2 Emulator (E2 emulator Lite) of RA/RE
1. Preface
The RTE0T00020KCAA0000J is an isolator for E2 Emulator and E2
emulator Lite.
This product is used for debugging in an environment where there is a
GND gap between the user system and the emulator system.
Package Components
Before using this product, please make sure that all the following items
are packed.
Table 1.1 Package Components
RTE0T00020KCAA0000J
RTE0T00020KCAC0000J
709441800(Wurth Elektronik)
R20UT5065JJ0100
R20UT5065EJ0100
LLWEB-10018513
Note: Please handle this product as precision equipment for transportation.
Important matter
Caution on Isolation Voltage:
This product is intended to isolate a small and electrically safe GND gap between the user system and
emulator system. In any case isolation voltage must be maintained within SELV limits i.e. less than
42.4VAC, or 60VDC.
The isolator must never be used as an element of a safety isolation system. The part could be expected to
function correctly at higher voltage across the isolation barrier; but then the circuitry on both sides of the
barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must
form a barrier between these circuits and any user-accessible circuitry according to safety standard
requirements.
Caution to Be Taken for Disposal:
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.
European Union regulatory notices:
The WEEE (Waste Electrical and Electronic Equipment) regulations put responsibilities on producers for the
collection and recycling or disposal of electrical and electronic waste. Return of WEEE under these
regulations is applicable in the European Union only. This equipment (including all accessories) is not
intended for household use. After use the equipment cannot be disposed of as household waste, and the
WEEE must be treated, recycled and disposed of in an environmentally sound manner. Renesas
Electronics Europe GmbH can take back end of life equipment, register for this service at
"http://www.renesas.eu/weee".
Cautions to Be Taken for Handling the Isolator:
Take full care not to touch any parts or cause short circuits on this product.
Protect this product from excessive physical shock.
Do not modify this product. Modifying the product will void your warranty.
Cautions for Use Temperature:
The isolator is to be used in an environment with a maximum ambient temperature of 35°C.
Care should be taken that this temperature is not exceeded.
R20UT5065EJ0100 Rev.1.00
Dec 2021
Item
Isolator for the E2 Emulator (E2 emulator Lite) of RA/RE
User interface cable (ARM20P-20Pcable)
Nylon Spacer
Japanese User's Manual (this material)
English User's Manual
List of hazardous toxic substances or elements
CAUTION
User's Manual
Sermon
Qty.
1
1
4
1
1
1
Page 1 of 8

Advertisement

Table of Contents
loading

Summary of Contents for Renesas RTE0T00020KCAA0000J

  • Page 1 After use the equipment cannot be disposed of as household waste, and the WEEE must be treated, recycled and disposed of in an environmentally sound manner. Renesas Electronics Europe GmbH can take back end of life equipment, register for this service at “http://www.renesas.eu/weee”.
  • Page 2: Specifications

    User's Manual RTE0T00020KCAA0000J CAUTION Cautions to Be Taken for Connecting the Isolator: Always switch OFF the power before connecting or disconnecting this product. • This product has some switches. Make settings depending on debugging interface you use. • Before changing settings power off this product and other connected devices.
  • Page 3: Notes On Usage

    2021-10 (21.10.0) or higher. Note on Programming Software: Use the Renesas Flash Programmer as the writing software. If you are unable to start the Renesas Flash Programmer, run e studio once. 4. Usage Sections 4.1 to 4.3 of this chapter use the E2 Emulator as an example. If you are using the E2 emulator Lite, read "E2 Emulator"...
  • Page 4 5. Jumper Pins (JP1 - JP6) Settings The jumper pin settings differ depending on the software used. If you are using the debugger (e2studio), see Section 5.1. If you are using the Renesas Flash Programmer, see Section 5.2. 5.1 Settings when using the debugger (e studio) Set the jumper pins (JP1 - JP6) of this product according to the settings of the debugger (e2studio).
  • Page 5 5.2 Settings when using Renesas Flash Programmer (Programming GUI) Set the jumper pins (JP1 - JP6) of this product according to the settings of the Renesas Flash Programmer. When (1) in Figure 5.2 is RA, set the jumper pins (JP1 - JP6) of this product according to RA in Table 5.2.
  • Page 6: External Dimensions

    User's Manual RTE0T00020KCAA0000J 6. External Dimensions 50 mm Figure 6.1 External Dimensions R20UT5065EJ0100 Rev.1.00 Page 6 of 8 Dec 2021...
  • Page 7: Warranty

    Failure or damage attributable to modifications, repairs, adjustments, or other acts made to the product by other than Renesas Electronics Corporation. (3) This product is accessories product. We cannot accept any request for repair. Please forgive the request for repair.
  • Page 8: Corporate Headquarters

    Renesas Electronics disclaims any and all liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user’s manual or other Renesas Electronics document.

Table of Contents