Subscribe to Our Youtube Channel
Related Manuals for Dahua DH-IPC-WDX2
Summary of Contents for Dahua DH-IPC-WDX2
- Page 1 Eyeball Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.0...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, configuration, general operation, and system maintenance of network camera. Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide ● Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened. ● All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. ●...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety ● All installation and operation shall conform to your local electrical safety codes. ● The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no higher than PS2. - Page 5 Quick Start Guide mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent to clean the device body, nor can strong, abrasive detergent be used. ●...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ........................................I Important Safeguards and Warnings ............................III 1 Introduction ......................................1 1.1 Cable ........................................ 1 1.2 LED Status ...................................... 1 2 Network Configuration ..................................3 2.1 Initializing Device ..................................3 2.2 Changing Device IP Address ..............................5 2.3 Logging in to Web Page ................................. -
Page 7: Introduction
Quick Start Guide 1 Introduction 1.1 Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see FAQ manual. Figure 1-1 Cables Table 1-1 Cable information Port Name Description ●... - Page 8 Quick Start Guide LED Status Device Status Flashing red and green Updating firmware.
-
Page 9: Network Configuration
Quick Start Guide 2 Network Configuration Device initialization and IP setting can be completed with the ConfigTool or on web page. For more information, see web operation manual. ● Device initialization is available on select models, and it is required at first-time use and after device is being reset. - Page 10 Quick Start Guide ● Enter username and the password when you want to change IP, configure the system, update the device, restart the device, and more. Step 5 Click OK. Step 6 Select one or several devices in uninitialized status, and then click Initialize. Select the devices to be initialized, and then click Initialize.
-
Page 11: Changing Device Ip Address
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates according to the actual needs. If neither, leave them unselected. Step 10 Click OK to initialize the device. Click the success icon ( ) or the failure icon ( ) for the details. -
Page 12: Logging In To Web Page
Quick Start Guide Figure 2-4 Change IP address ● IP addresses of multiple devices will be set to the same if you select the Same IP checkbox. ● If DHCP server is available on the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP. -
Page 13: Operating With Dmss
Quick Start Guide 3 Operating with DMSS Make sure that there are no obstacles and electromagnetic interference between the device and the router for best possible wireless performance. Step 1 Add the device. 1) Tap + button on the upper-right corner of the DMSS home page to scan the QR code on the camera. - Page 14 Quick Start Guide Figure 3-2 Configure the device hotspot Step 3 Configure the Wi-Fi. Select your Wi-Fi network from SSID list and then enter the password. Step 4 Configure the device information. 1) Create the device name and password. 2) Set the time zone and then click Done. Figure 3-3 Configure the device information...
-
Page 15: Installation
Quick Start Guide 4 Installation 4.1 Packing List ● The tool required for the installation such as electric drill is not provided in the package. ● The operation manual and related tool information are contained in the disk or the QR code. Figure 4-1 Packing list 4.2 Dimensions Figure 4-2 Dimensions (mm [inch]) -
Page 16: Installing Camera
Quick Start Guide 4.3 Installing Camera 4.3.1 Installation Method Figure 4-3 Installation method 4.3.2 Installing SD Card ● SD card slot is available on select models. ● Disconnect the power before installing or removing the SD card. ● Do not open the cover for a long time to avoid spray in cameras. Press the reset button for 10 seconds to reset the device. -
Page 17: Attaching Camera
Quick Start Guide 4.3.3 Attaching Camera ● Make sure that the mounting surface is strong enough to hold at least three times the weight of the camera and bracket. ● Remove the protective film after finishing installation. Figure 4-5 Cable going through the side cable tray Figure 4-6 Cable going through the mounting surface... -
Page 18: Optional) Installing Waterproof Connector
Quick Start Guide 4.3.4 (Optional) Installing Waterproof Connector This part is needed only when a waterproof connector comes with the camera and the camera is used outdoors. Figure 4-7 Install waterproof connector... -
Page 19: Adjusting Lens Angle
Quick Start Guide 4.3.5 Adjusting Lens Angle Figure 4-8 Adjust lens angle... - Page 20 Quick Start Guide...
Need help?
Do you have a question about the DH-IPC-WDX2 and is the answer not in the manual?
Questions and answers