Anritsu OSL Series Instruction Manual
Hide thumbs Also See for OSL Series:

Advertisement

®
Advanced Test Equipment Rentals
www.atecorp.com 800-404-ATEC (2832)
WARRANTY
The Anritsu product(s) listed on the title page is (are) warranted against defects in
materials and workmanship for one year from the date of shipment.
Anritsu's obligation covers repairing or replacing products which prove to be defective
during the warranty period. Buyers shall prepay transportation charges for equipment
returned to Anritsu for warranty repairs. Obligation is limited to the original purchaser.
Anritsu is not liable for consequential damages.
LIMITATION OF WARRANTY
The foregoing warranty does not apply to Anritsu connectors that have failed due to
normal wear. Also, the warranty does not apply to defects resulting from improper or
inadequate maintenance by the Buyer, unauthorized modification or misuse, or operation
outside of the environmental specifications of the product. No other warranty is
expressed or implied, and the remedies provided herein are the Buyer's sole and exclusive
remedies.
DISCLAIMER OF WARRANTY
DISCLAIMER OF WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, ANRITSU COMPANY AND ITS SUPPLIERS DISCLAIM ALL
WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH REGARD TO THE SOFTWARE PRODUCT. THE
USER ASSUMES THE ENTIRE RISK OF USING THE PROGRAM. ANY LIABILITY
OF PROVIDER OR MANUFACTURER WILL BE LIMITED EXCLUSIVELY TO
PRODUCT REPLACEMENT.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ANRITSU COMPANY OR
ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL
DAMAGES
WHATSOEVER
(INCLUDING,
WITHOUT
LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION,
LOSS
OF
BUSINESS
INFORMATION,
OR
ANY
OTHER
PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THE
SOFTWARE PRODUCTS, EVEN IF ANRITSU COMPANY HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
NOTICE
Anritsu Company has prepared this manual for use by Anritsu Company personnel and
customers as a guide for the proper installation, operation and maintenance of Anritsu
Company equipment and computer programs. The drawings, specifications, and
information contained herein are the property of Anritsu Company, and any
unauthorized use or disclosure of these drawings, specifications, and information is
prohibited; they shall not be reproduced, copied, or used in whole or in part as the basis
for manufacture or sale of the equipment or software programs without the prior written
consent of Anritsu Company.
UPDATES
Updates, if any, can be downloaded from the Documents area of the Anritsu web site at:
http://www.us.anritsu.com
For the latest service and sales information in your area, please visit:
http://www.anritsu.com/contact.asp

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OSL Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Anritsu OSL Series

  • Page 1 Anritsu Company. UPDATES Updates, if any, can be downloaded from the Documents area of the Anritsu web site at: http://www.us.anritsu.com For the latest service and sales information in your area, please visit:...
  • Page 2 Before you export this product or any of its manuals, please contact Anritsu Company to confirm whether or not these items are export-controlled. When disposing of export-controlled items, the products and manuals need to be broken or shredded to such a degree that they cannot be unlawfully used for military purposes.
  • Page 3 Safety Symbols To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Company uses the following symbols to indicate safety-related information. For your own safety, please read the information carefully before operating the equipment. Symbols Used in Manuals...
  • Page 4 Some or all of the following five symbols may or may not be used on all Anritsu equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this manual.
  • Page 5: Table Of Contents

    Return Loss Verification Procedures ... 2-5 Open and Short 180° Phase Shift Verification ..2-6 Precision Load DC Resistance Verification ..2-7 Model OSL Series CG PN: 10100-00055 Rev. B Contents-1...
  • Page 6 Contents-2 PN: 10100-00055 Rev. B Model OSL Series CG...
  • Page 7: Chapter 1-General Information

    Chapter 1 — General Information Introduction This guide provides performance verification procedures for Anritsu Model OSL Series Open/Short/Load Calibration Tees. Description The model OSL Series family consists of the following models: Table 1-1. OSL Series Precision Open/Short/Load Calibration Tees Anritsu Part Number...
  • Page 8: Recommended Test Equipment

    Impedance: 50 Ohm Calibration Kit Anritsu Model SC6650 Termination: sliding termination Adapter Connector: N(m) to K(f) Anritsu Model 34NKF50 Adapter Connector: N(f) to K(f) Anritsu Model 34NFKF50 Digital Agilent Model 34401A Multi-meter PN: 10100-00055 Rev. B Model OSL Series CG...
  • Page 9: Chapter 2-Performance Verification

    Chapter 2 — Performance Verification Introduction This chapter contains tests that can be used to verify the performance of the OSL Series Open/Short/Load Calibration Tees. The tests include: • Return Loss Verification • Open and Short 180° Phase Shift Verification •...
  • Page 10: Specifications

    Performance Verification Specifications Refer to Table 2-1 for the OSL series specifications. Table 2-1. OSL Series Specifications Anritsu Part Number OSLN50LF OSLN50-1 OSLN50 Specification OSLNF50LF OSLNF50-1 OSLNF50 Frequency DC to 4 GHz DC to 6 GHz DC to 18 GHz...
  • Page 11: Verification Procedures

    “Open and Short 180° Phase Shift Verification” on page 2-6 • “Precision Load DC Resistance Verification” on page 2-7 Equipment Required • Anritsu Model 37247D or 37347D Vector Network Analyzer • Anritsu Model SC6650 N Connector Calibration Kit • Anritsu Model 34NKF50 or 34NFKF50 Adapter Model OSL Series CG...
  • Page 12: Vna Calibration Procedure

    1. Allow the VNA to warm up for a minimum of 1 hour. 2. Install an appropriate adapter to the VNA Port 1 so the test port has a connector that can mate to the OSL Series Open/Short/Load Calibration Tee. For example, install a 34NFKF50 adapter to VNA Port 1 when testing a male Open/Short/Load Calibration Tee.
  • Page 13: Return Loss Verification Procedures

    For OSLN50 and OSLNF50, the return loss is specified for 3 frequency bands. The rotary knob should be used to move the Marker 1 to read out the worst case return loss in each band. Model OSL Series CG PN: 10100-00055 Rev. B...
  • Page 14: Open And Short 180° Phase Shift Verification

    4. Remove the SHORT and connect the OPEN of the same DUT Calibration Tee to the adapter on VNA Port 1. 5. The displayed trace must be within the limit lines to pass the specification. The actual value can be verified using markers. PN: 10100-00055 Rev. B Model OSL Series CG...
  • Page 15: Precision Load Dc Resistance Verification

    Use an Ohmmeter to measure the DC resistance between the outer conductor and center conductor of the Precision Load and verify that it is within specification (refer to Table 2-1, “OSL Series Specifications). Model OSL Series CG PN: 10100-00055 Rev. B...
  • Page 16 PN: 10100-00055 Rev. B Model OSL Series CG...
  • Page 18 Anritsu Company 490 Jarvis Drive Anritsu Prints on Recycled Paper with Vegetable Soybean Oil Ink Morgan Hill, CA 95037-2809 http://www.anritsu.com/...

This manual is also suitable for:

Osln50lfOslnf50lfOsln50-1Oslnf50-1Osln50Oslnf50

Table of Contents