Pentax MZ-S Service Manual page 22

5 5 5 5 - - - - 5.0 5.0 5.0 5.0- - - - A4(Back door key) A4(Back door key) A4(Back door key) A4(Back door key)
1） A95
2） Apply L115 at 2 positions on Main body.
3） T64･･･Apply G151 on the land of back door SW.
Wipe off SW land contact for mid-roll rewind.
4）0-A4, 1 screw, A6
5 5 5 5 - - - - 6.T61(Data flex) 6.T61(Data flex) 6.T61(Data flex) 6.T61(Data flex)
1） Insert T61 into square hole of main Body.
2） Install contact portion of T61. A27、A189 x3
3） Align soldering portion of T61 with positioning post
and adhere DT.
5 5 5 5 - - - - 7. Elec 7. Electric contact and related parts. tric contact and related parts.
7. Elec 7. Elec tric contact and related parts. tric contact and related parts.
1） Install A35 with 1 screw･･･Insert 2 black lead wires into main body.
2） Arrange 2 lead wires. A40.
3） A34･A33･A32
4） A31 x2･･･Adhere to the Main body. Do not touch with
A32.
5 5 5 5 - - - - 8. 0 8. 0- - - - S200 (Winding Motor) S200 (Winding Motor)
8. 0 8. 0 S200 (Winding Motor) S200 (Winding Motor)
1） C35･0-S200, C12, 2 screws･･･Pass 2 lead wires through C12.
(Black lead wire connect to Battery chamber)
2） Apply G126 onto the gear teeth of 0-S200.
3） Tighten film retainer with 2 screws while avoiding 0-T27 flex
from being damaged.
5 5 5 5 - - - - 9.C1 9.C1 9.C1 9.C1･ ･ ･ ･ C2(Winding base plate A .B) C2(Winding base plate A .B) C2(Winding base plate A .B) C2(Winding base plate A .B)
1） C11･･･Apply G134 inner wall at top and button.
Make sure not to scratch film retainer Plate
2） Install C1 securely. 3 retainer screws.
3） Make sure that C11 turns smoothly.
4） Apply G126 at 6 positions of gear shafts.
5） Install gears.
6） Install C2 from the hook portion and
tighten with 1 screw.
5 5 5 5 - - - - 10. A22(Film guide) and related parts. 10. A22(Film guide) and related parts.
10. A22(Film guide) and related parts. 10. A22(Film guide) and related parts.
Install as shown in fig. and adhere A26 securely
aligning screw hole and post on A26.
5 5 5 5 - - - - 11.0 11.0- - - - E000(Shutter block) 11.0 11.0 E000(Shutter block) E000(Shutter block) E000(Shutter block)
1） Install mechanical portion first.
2） Push towards side of grip and tighten A50 for
temporarily.
3） Tighten 2 screws for temporarily and then
tighten screws in the numerical order.(①､②､③)
4） To avoid troubles for shutter curtain,
Back door should be installed.
A32
A31
27640 -21/34-
①
②
③