Adj·chck] Af Joint Operating Stroke; Adj·chck]Viewfinder Focus Parllux - Pentax MZ-S Service Manual

3） W65(t=0.5) x3, M 103 x3
4） [ [ [ [ Adjust Adjust] ] ] ] Install AF block for temporary.
Adjust Adjust
Tighten M103 until it stops and then
return for about 1.5 turns.
(If the final adjustment is over, apply screw lock
between M103 and W65. )
[ [ [ [ Note Note Note Note] ] ] ] There should not be any dust, hair or
stain on AF window of 0-M100.
4 4 4 4 - - - - 9 9 9 9 . 0 . 0- - - - S300(AF Motor block) . 0 . 0 S300(AF Motor block) S300(AF Motor block) S300(AF Motor block)
5） Adhere S364 onto 0-S300.
6） Arrange lead wires and Flexi. as shown in Fig.
7） 0-S300, 2 screws.(Apply screw lock.)
8） Arrange lead wires.
4 4 4 4 - - - - 10. 10. 10. [A 10. [A [A [Adjust djust djust djust･ ･ ･ ･ Check] AF joint stroke. Check] AF joint stroke. Check] AF joint stroke. Check] AF joint stroke.
[Prepared material] Caliper
1) Set Focus mode lever at "AF". If 0-I331 is installed, set at the lowest one.
2) [Check] [Check] [Check] When removing finger from Mount lock lever, AF joint pin(0-S300) should be [Check]
stuck out more than 1.2mm above body mount.
3) [Check] [Check] While pushing mount lock lever and mount lock pin become same height with [Check] [Check]
camera mount, AF joint pin should not exceed the surface of camera mount.
[Adjust] Adjusting can be done by turning eccentric screw of 0-A121(Joint connecting [Adjust] [Adjust] [Adjust]
lever). Apply screw lock on the eccentric screw.
5） [Check] [Check] After depressing mount lock lever and then
[Check] [Check]
set free, 0-A121 should return smoothly.
4 4 4 4 - - - - 1 1 1 1 1 1 1 1 . . . . L3 L3・ ・ ・ ・ L2(Penta Prism L2(Penta Prism・ ・ ・ ・ Focus screen)
L3 L3 L2(Penta Prism L2(Penta Prism
1） M3
2） L3（M8 x2,M18,M19） ･･･Loosen M16 x2 beforehand.
3） M61、M62 x2(Hook M61 to M63)
4） 0-M301、2 screws.
5） M22(Install –00C for temporary adjustment), L2
4 4 4 4 - - - - 12 12 12. [Adjust 12 . [Adjust . [Adjust . [Adjust･ ･ ･ ･ Check] Focus in finder Check] Focus in finder・ ・ ・ ・ Parallax Check] Focus in finder Check] Focus in finder
[Preparation [Prepar [Prepar [Prepar ation ation] ] ] ] Collimator、Focus master lens. ation
1） Adjust diopter by turning 0-M301 at center of frame.
2）[Adjust [Adjust･ ･ ･ ･ Check] [Adjust [Adjust Check] Check] Check] Parallax
Tolerance Tolerance： ： ： ： Left & Right less than 1° Tolerance Tolerance
Horizontal Horizontal Horizontal Horizontal
Horizontal Parallax can be adjusted by M16 x2.
Apply screw lock onto M16.
3）[Adjust] [Adjust] [Adjust] View finder focus. [Adjust]
Adjusting washer (M22-000A～I).
Tolerance Tolerance Tolerance Tolerance： ： ： ： 0 0 0 0 ± ± ± ± 0.04 mm
4).Make sure that dust, hair and stain should not be observed on
focus screen and on the Penta prism.
Focus screen)
Focus screen) Focus screen)
Left & Right less than 1° Left & Right less than 1° Left & Right less than 1°
less than 1° 50´ less than 1° 50´ less than 1° 50´ less than 1° 50´
0.04 mm(Center 0.04 mm 0.04 mm (Center (Center φ φ φ φ 10mm) (Center
0 0 0 0 ± ± ± ± 0.07 m 0.07 mm m m m (Other than center) (Other than center)
0.07 m 0.07 m (Other than center) (Other than center)
27640 -19/34-
Parallax. . . . Parallax Parallax
10mm) 10mm) 10mm)
S364 0-S300