Download Print this page

Advertisement

Quick Links

Kit contents GK-ECULMB48M-00XX:
("XX" bike model e.g. KTM 300 EXC TPI=08)
ECU racing GET, Map switch and harness, WiFiCOM,
installation manual
Kit contents GK-KIT2TI-00XX:
("XX" bike model e.g. KTM 300 EXC TPI=00)
Injectors support kit, ECU racing GET, Map select and
harness, WFCOM, installation manual
E
C
U
I
N
S
T
A
L
L
A
T
E
C
U
I
N
S
T
A
L
L
A
T
I
N
S
T
A
L
L
A
Z
I
O
N
E
I
N
S
T
A
L
L
A
Z
I
O
N
E
1
PUSH
2
1-Disconnect the positive battery pole and unhook the
ECU connector
ATTENTION: if you have the GET injectors support
kit, procced with "INJECTOR SUPPORT
INSTALLATION "
2- pass the cable tie provided under the OEM harness
3- connect the GET ECU and fix it by the cable tie
4- When you put the saddle, the ECU must be in the
middle of saddle protuberances
K
T
M
E
K
T
M
E
H
U
S
Q
V
A
H
U
S
Q
V
A
G
A
S
G
G
A
S
G
I
O
N
:
I
O
N
:
C
E
N
T
R
A
L
I
N
A
:
C
E
N
T
R
A
L
I
N
A
:
3
GD-MIP-0039-AC_rev02
X
C
2
5
0
/
3
0
0
T
P
I
X
C
2
5
0
/
3
0
0
T
P
R
N
A
T
E
2
5
0
/
3
0
R
N
A
T
E
2
5
0
/
3
0
A
S
E
C
2
5
0
/
3
0
0
A
S
E
C
2
5
0
/
3
0
0
Contenuto GK-ECULMB48M-00XX:
("XX" modello moto Es. KTM 300 EXC TPI= 08)
ECU Racing GET, cablaggio e selettore mappa, WiFiCOM,
manuale istruzioni.
Contenuto GK-KIT2TI-00XX:
("XX" modello moto Es. KTM 300 EXC TPI= 00)
Kit supporto iniettori, ECU Racing GET, cablaggio e selettore
mappa, WFCOM, manuale di istruzioni.
1
1- Disconnettere il polo positivo della batteria (sotto sella) e
togliere la ECU originale sganciandola dal connettore
ATTENZIONE: se si dispone di un kit sopporto iniettori
GET, procedere con "INSTALLAZIONE SUPPORTO
INIETTORI"
2- Passare la fascetta fornita sotto il cablaggio originale
3- connettere la ECU GET e fissare il connettore con la
fascetta precedentemente passata sotto i cavi
4- rimontare la sella ponendo attenzione che la ECU GET
stia esattamente tra le protuberanze del sotto sella
athena.eu
I
0
i
0
i
sales.get@athena.eu
2
4

Advertisement

loading
Need help?

Need help?

Do you have a question about the GK-ECULMB48M-00 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Athena GK-ECULMB48M-00 Series

  • Page 1 4- When you put the saddle, the ECU must be in the 4- rimontare la sella ponendo attenzione che la ECU GET middle of saddle protuberances stia esattamente tra le protuberanze del sotto sella   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 2 5- remove from the bike the “injector group” and disassemble it come in foto. Il tubo benzina più lungo (F) non verrà like the photo. The fuel hose will not be needed (F) in the next utilizzato per il prossimo passaggio. step   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 3 11- Fissare i tubi benzina come in foto, (riferimento 5). Where necessary use the metal band and the fuel hose materiale passaggio 5). Dove necessario utilizzare le provided. fascette metalliche ed il tubo benzina fornito a corredo   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 4 12- Fix the injector support GET and the intake flange with the provided screws M6x30 and the OEM gasket. Assemble the bike (fuel tank, injector’s connectors, throttle body, VITI M6X30 “GET” air box - back frame, exhaust, “GET” SCREW M6X30 saddle).   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 5 BATTERIA LA ECU E’ PROGRAMMABILE SOLO SE COLLEGATA AL THE ECU MUST BE CONNECTED TO THE VEHICLE CABLAGGIO MOTO CON “WAKE UP CONNECTOR” HARNESS WITH THE WAKE UP CONNECTOR CONNECTED TO BE PROGRAMMED . COLLEGATO   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 6 BATTERIA LA ECU E’ PROGRAMMABILE SOLO SE COLLEGATA AL THE ECU MUST BE CONNECTED TO THE VEHICLE CABLAGGIO MOTO CON “WAKE UP CONNECTOR” HARNESS WITH THE WAKE UP CONNECTOR CONNECTED TO BE PROGRAMMED . COLLEGATO   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 7 SET 3 Alla richiesta, confermare premendo YES – 4 Per modificare il breakpoints, selezionarlo, esclusi gli estremi, e modificarlo con , quindi inviare con il tasto SET e confermare con YES   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...
  • Page 8 No standard (OEM) air filter and/or exhaust system may loss engine power • Don’t change or modify the parts supplied by Athena • Warning: the dash power consumption indicator and FI System Error messages aren’t available when GET ECU is installed.
  • Page 9 ADJUST IDLE SCREW Avvitare COMPLETAMENTE la vite del minimo, poi aprirla di: 2,5 giri MY 2018/2019 4,5 giri MY 2020/2021 Screw the idle screw COMPLETELY and then open it: 2,5 turns MY 2018/2019 4,5 turns MY 2020/2021   GD-MIP-0039-AC_rev02 athena.eu sales.get@athena.eu...

This manual is also suitable for:

Gk-kit2ti-00 seriesGk-kit2ti-0001