Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for barbas Wi-Fi Box / Puck
Summary of Contents for barbas Wi-Fi Box / Puck
- Page 1 Installation and user manual Wi-Fi Box / Puck...
- Page 2 Barbas Bellfires BV. This document could contain technical inaccuracies or typographical errors. Barbas Bellfires BV reserves the right to revise this document from time to time in the contents thereof.
- Page 3 Contents...
-
Page 4: About This Document
The illustrations are for instructional use only. Screenshots of the 'Barbas Bellfires Gas' app are from an Apple IPad. The screenshots of the 'Barbas Bellfires Gas' app on other mobile devices can be... -
Page 5: How To Work With This Document
How to work with this document How to work with this document Make yourself familiar with the structure and content of the document. Read the safety chapter in detail. Make sure that you understand all the instructions. Do the procedures completely and in the given sequence. Warnings and cautions used in this document Warning If you do not obey these instructions, there is a risk that can cause personal injury or... -
Page 6: Intended Use
Wi-Fi Box The Wi-Fi Box is intended for indoor use in combination with a Bellfires gas appliance and with the 'Barbas Bellfires Gas' app in combination with a hand set or Puck. Do not use it for other purposes. 3.1.2 Puck The Puck is intended for indoor use in combination with a Bellfires gas appliance. -
Page 7: Led Indication
Description 3.2.2 LED indication The Wi-Fi Box has two LED's with colors red/green/blue. Item Description LED 1 Green Connected to receiver Not connected to receiver Standby mode is active. No power supply LED 2 Green Connected to the home network (router) Blue blinking A Wi-Fi network has been detected Not connected to the home network (router) - Page 8 Requirements Requirements Wi-Fi router (for Wi-Fi Box only) Minimum requirements Wi-Fi router: • Compatible with IEEE 802.11n/g/b • WPA2 encryption • Radio frequency: 2.4 GHz • Wireless auto channel: Automated search for Wi-Fi radio channel free of interference • Support of the User Datagram Protocol (UDP) •...
- Page 9 Installation of the Wi-Fi Box Installation of the Wi-Fi Box Make sure you have a Symax-2 receiver and a Symax-2 handset (8 or 10 buttons). Both can be recognized by the blue sticker. If not, contact your dealer. Connect the 4-wire cable on the connector marked 'SI ' on the receiver. Connect the other side of the 4-wire cable on the connector marked 'receiver' on the Wi-Fi Box Make sure LED 1 is green.
- Page 10 Connecting the Puck Connecting the Puck Remove the lid of the battery compartment at the back of the Puck. Put 2 batteries (type AAA, 1.5 Volt) in the battery compartment. Make sure the batteries are put correctly as indicated in the battery holder. Put the lid on the battery compartment.
- Page 11 Setup Setup Note: Screen shots shown in this manual are for an Apple iPad. The 'Barbas Bellfires Gas' app screen on an iPhone or Android mobile device can look different on details. The functionality and use is the same as described in this manual.
- Page 12 Agree with the Terms and Condi- tions. • Select Register Confirm your registration by clicking on the link in the e-mail that has been sent to you. Upon successful verification of your account, you can login on the 'Barbas Bellfires Gas' app.
- Page 13 Setup • Return to the 'Barbas Bellfires Gas' app. • Fill in the login details and ac- cept the Terms and Conditions. • Select Login. Connecting to the home network with KWIK connect Note: • Make sure the router obeys the requirements. Refer to chapter details.
- Page 14 Setup The 'Barbas Bellfires Gas' app starts to connect the Wi-Fi Box to the selected home network. If connection is successful proceed with Fireplace settings. Continue the instructions in chapter If connection is unsuccessful se- lect Standard Setup. Continue the...
- Page 15 Note: For Apple iOS mobile devices: The message 'No internet connection' is to be ig- nored • Go back to the 'Barbas Bellfires Gas' app • The name of the home network that has to connected is shown. • Select OK.
-
Page 16: Appliance Settings
Setup Note: Refer to chapter if the connection with Standard Setup failed. Appliance settings • Give the appliance a name. • Select the checkmark on the right to confirm the name. • Select a symbol for the appli- ance • Select the available options. -
Page 17: Operating The Appliance
Operating the appliance Operating the appliance Start screen All functions of the 'Barbas Bellfires Gas' app are accessible from the menu or the icons on the start screen. Number Option Description ON/OFF button To start or stop the appliance. Note: After switch to OFF of the appliance, wait 30... -
Page 18: Description Of The Symbols
Operating the appliance Description of the symbols 8.2.1 Menu symbols Symbol Function Description Profiles Define or choose your personal operating profile. Maximum 4 user profiles can be set, Manual mode Manual adjustment of the flame height. Thermostatic mode Automatic adjustment of the heat output based on the set room temperature and the measured room temperature. -
Page 19: Other Symbols
Operating the appliance Symbol Function Description Fireplace settings General appliance settings Help Help pages with information about the menu func- tions 8.2.2 Other symbols Symbol Function Description Home Go to the start screen ON / OFF Start or stop the appliance Outside temperature Shows the outside temperature measured by a nearby weather station... - Page 20 Operating the appliance Main menu 8.3.1 Profiles Define a maximum of 4 user profiles. Set a user profile Select one of the four user profiles. The selected user profile shows in the left hand corner of the screen. Select a function that must be included in the selected profile and set this function to the correct value or correct position.
- Page 21 Operating the appliance 8.3.2 Manual operation • Set the flame height by selecting one of the segments in the circle. • Select one of the three pre-defined settings with the three buttons on the bottom of the screen. Options are Low flame, Standby (pilot flame is ON) and High flame. •...
- Page 22 Operating the appliance 8.3.3 Thermostatic operation Control the room temperature with the thermostat. • Set the required room temperature by selecting a segment of the circle. During this selection the set temperature shows in the center of the circle. • After selection of the required temperature, the room temperature is shown in the center of the circle.
- Page 23 Operating the appliance 8.3.4 Timer Set the time interval after which the appliance switches to off. Set a time duration. The maximum time duration is 9 hours and 59 minutes. Press the Power button to start the timer. Press the Power button again to stop the timer. Note: At the end of the set time duration the appliance is set to OFF (the pilot 8.3.5 flame is also off).
-
Page 24: Program Mode
Note: Before use of the Program mode make sure the time in the Wi-Fi Box is synchronized with the time of the mobile device. Open the settings page in the 'Barbas Bellfires Gas' app. Press under 'Fireplace settings' on the name of the appliance. - Page 25 Operating the appliance Set a program Select one of the eight available programs by pressing on the number of the program Set the start time and the start temperature by selecting the green segments. Set the days of the week. Individual days, all 7 days, weekdays or weekends can be set.
-
Page 26: Eco Mode
Operating the appliance 8.3.6 ECO mode ECO mode makes it possible to change the flame height automatically during a set time cycle. Saves gas in comparison with manual mode or thermostatic mode. Set a flame cycle Select ECO mode from the menu. Select Low fire, Medium fire or High fire by pressing one of the three flame icons on the bottom of the screen. - Page 27 Operating the appliance 8.3.7 Fan (optional) This function is only available if the appliance has a ventilator. Set the fan speed by selecting the preferred speed 1 to 4. Press the Power button on the bottom of the screen. Press the Power button on the bottom of the screen again to stop the ventilator. Note: The fan starts always with speed '4'.
-
Page 28: Lighting (Optional)
Operating the appliance 8.3.8 Lighting (optional) This function is only available when the appliance has lighting Select lighting from the menu. Press Power button to switch lighting to ON. Lighting switches to last set intensity. Change the lighting intensity by swiping over the lightbulb in vertical direction. Press Power button again to switch lighting to OFF. -
Page 29: Safety Lock
Operating the appliance 8.3.10 Safety lock With active safety lock, it is not possible to use the functions of the 'Barbas Bellfires Gas' app. It is only possible to switch the appliance to OFF. Activating the safety lock Open the main menu Press the Safety lock icon for two seconds. - Page 30 Operating the appliance with the Puck Operating the appliance with the Puck Start the appliance Press and hold the ON/OFF button until two short beeps confirm the start of the start-up sequence. The main burners start when the pilot flame ignition is confirmed.
-
Page 31: Troubleshooting
Wi-Fi Box for 20 sec- works. onds (refer to chapter 3.2.1 and end of this chap- ter). stop and start the 'Barbas Bellfires Gas' app and try to connect the Wi-Fi Box again. Contact your dealer if the prob- lem stays. - Page 32 A set program does not start The internal clock of the Wi-Fi Open the settings page in and stop the appliance on the Box is not synchronized with the 'Barbas Bellfires Gas' correct time. the internal clock of the mobile app. device.
- Page 33 F28, on-demand pilot Pilot flame goes off after 5 Start the appliance with the days, when during that com- handset or the 'Barbas Bellfires plete period the pilot flame was Gas' app. on continuously, but the main burners were not operated.
- Page 34 Wi-Fi Box and the receiver. Also, if applicable and possible, make screen shots of the error code that shows in the 'Barbas Bellfires Gas' app or make a screen shot of the screen when the problem occurred.
-
Page 35: Technical Data
Technical data Technical data Wi-Fi Box Puck Temperature range 0 ºC - 80 ºC 0 ºC - 55 ºC Radio frequency 2.4 GHz 868 MHz Power supply 230 VAC / 6 VDC 2 x 1.5 V 'AAA' alkaline batter- Wireless communication •... -
Page 36: Warranty Terms
Barbas appliance or Bellfires appliance. If a certain part is eligible for the warranty and the original part is no longer available, Barbas Bellfires B.V. shall ensure that an alternative part of at least the same quality shall be provided. - Page 37 Article 5: Warranty period This warranty will only be granted during the warranty period. The body of the Barbas appliance and Bellfires appliance is guaranteed for a period of 10 years against construction and/or material faults, starting from the moment of purchase.
- Page 38 Warranty Terms...
- Page 39 Warranty Terms...
- Page 40 002 - 19.04.2021 - 342810...
Need help?
Do you have a question about the Wi-Fi Box / Puck and is the answer not in the manual?
Questions and answers