Arris DG9450 Quick Start Manual

DG9450
WI-FI GATEWAY
Quick Start Guide
Caring for the environment by recycling
Please recycle product packaging and this document.
When you see this symbol on an ARRIS product, do not dispose of the product with
residential or commercial waste. Some countries or regions have set up systems to
collect and recycle electrical and electronic waste items. Recycling information can be
obtained from the WEEE recycling section at www.CommScope.com.
Please recycle product packaging and this document.
ARRIS, 3871 Lakefield Drive, Suwanee, GA 30024, USA
Front view and LED status
LED status
The LED status indicates the power status and
operating status of your DG9450.
Green
Purple
Blue
Flashing Blue
and Green
Flashing Purple
LED status
Rear view
2.5GigE Ethernet
For high speed
connection
to home device
1GigE Ethernet
For connection
to home device
MoCA LED
Indicates MoCA
connectivity with
other devices
Placement and safety information
The device complies with the applicable
requirements for performance,
construction, labeling, and information
when used as outlined below:
Caution: Risk of shock. Mains voltages
inside this unit. No user serviceable parts
inside. Refer service to qualified personnel
only!
• The device shall be cleaned using only
a damp, lint-free, cloth. No solvents or
cleaning agents shall be used.
• Do not use spray cleaners or aerosols on
the gateway.
• When the device is connected to a local
computer through Ethernet cables, the
computer must be properly grounded
to the building/residence AC ground
network. All plug-in cards within the
computer must be properly installed and
www.commscope.com
grounded to the computer frame per the
619020-001_1
1
Set up your Wi-Fi connection
Your DG9450 replaces both your modem and router to provide high-
speed wireless access to the Internet in a single device!
Use a coax cable to attach the cable port to your cable outlet or splitter,
then connect the power adapter to the power port, and plug it into an
AC power outlet.
Wi-Fi ready
The first time you power on your DG9450, it may take 15-20 minutes to
download and upgrade its firmware.
Wi-Fi error
To set up your personal device (computer, phone or tablet)
Power on, no Wi-Fi
Connect your device Wi-Fi using the network name or
Firmware upgrade in progress
SSID (ARRIS-####) and the password (Wi-Fi PWD)
shown on the security label on the bottom of your
WPS button pressed
DG9450.
Alternatively, you can use the included Ethernet cable to
connect to one of the yellow Ethernet ports.
If your device supports WPS (Wireless Protected Setup),
you can press the WPS button on the back of your
DG9450 and then activate WPS on your device to easily
connect your device.
For advanced options, proceed to step 2
WPS button
Connects a wireless
device with the DG9450
2
Advanced wireless configuration (optional)
If you want to change the default broadcasted SSID name or password
or any other advanced configuration, follow these steps:
Reset button
1. On your home device open a browser and go to http://192.168.0.1/
Press to power cycle
to access the wireless router setup. You may be prompted by a
the device
certificate error, this is normal and you can continue safely.
Power
2. The default user name is admin, and the default password is the
Connect to AC power
Wi-Fi PWD listed on the product label on the bottom of your DG9450.
Cable
Your user name and password are case-sensitive.
Connect to cable outlet
3. Enter the user name and password, and click Login.
INNOVATION, SCIENCE AND ECONOMIC
manufacturer's specifications. DEVELOPMENT CANADA STATEMENT:
• Ensure proper ventilation. Position the This device complies with Innovation,
Science and Economic Development
device so that air flows freely around it
Canada's license-exempt RSSs. Operation
and the ventilation holes on the unit are
is subject to the following two conditions:
not blocked.
(1) This device may not cause interference;
• Do not mount the device on surfaces that
and
are sensitive to heat and/or which may
(2) This device must accept any
be damaged by the heat generated by
interference, including interference that
the modem, its power supply, or other
may cause undesired operation of the
accessories.
device.
• Never place the device on top or close to
Caution:
any heat sources such as other electronic
(i) the device for operation in the band
devices. Doing so will reduce life time
5150–5250 MHz is only for indoor use
and may cause irreparable damage or
to reduce the potential for harmful
malfunction.
interference to co-channel mobile satellite
• The device is designed to stand on a
systems;
horizontal surface.
(ii) for devices with detachable antenna(s),
• Note that metallic surfaces and objects
the maximum antenna gain permitted for
can interfere with the operation of Wi-Fi
devices in the bands 5250-5350 MHz and
wireless technology .
5470-5725 MHz shall be such that the
Security label
.
equipment still complies with the e.i.r.p.
limit;
(iii) for devices with detachable antenna(s),
the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall
be such that the equipment still complies
with the e.i.r.p. limits specified for point-
to-point and non-point-to-point operation
as appropriate.
RADIATION EXPOSURE STATEMENT:
This equipment complies with Canada
radiation exposure limits set forth for
an uncontrolled environment. This
equipment should be installed and
operated with minimum distance 20cm
between the radiator and your body.
CANADIAN COMPLIANCE
This Class B digital apparatus meets
all requirements of the Canadian
Interference Causing Equipment
Regulations and CAN ICES-003 (B)/
NMB-003(B).