Related Manuals for BN Products BNHC-20
Summary of Contents for BN Products BNHC-20
- Page 1 PRODUCT: BNHC-20 REBAR CUTTER OPERATIONS MANUAL 3450 Sabin Brown Road • Wickenburg, AZ 85390 (800) 992-3833 • mail@bnproducts.com | 1 | www.bnproducts.com BN Products-USA...
- Page 2 As a result of revisions and other on going updates, the contents of this manual may be slightly different from the actual product. BN Products reserves the right to make changes at any time, without notice and without incurring any obligation, please understand.
- Page 3 A foot operated switch and special electrical box are available if you want to use these cutters as production tools. Contact your local distributor or BN Products-USA, LLC. RESTRICT USE TO DESIGNATED MATERIALS There is always a chance that the cut end may shoot out, especially if less than 30cm (1 foot) in length.
- Page 4 (anti-foam anti-abrasion): Tellus 68 (Shell), Rando HD 68 (Texaco) or Chevron AW 68 (Chevron). Hydraulic oil can also be ordered in quart con- tainers from your BN Products Distributor. OPERATING INSTRUCTIONS CAUTION: Indicates hazard that could result in minor person- al injury and/or product damage.
- Page 5 Before plugging in the tool, make sure that the switch lock is OFF. CAUTION: If switch lock is ON, cutter will start as soon as it is plugged in. To disengage lock, pull trigger-switch and press lock-button, which will pop out. | 5 | www.bnproducts.com BN Products-USA...
-
Page 6: Points Of Attention
CAUTION: Flying ends are a hazard to all personnel in the vicinity. Erect safety screens. 2. Do not cover air vents or operate the tool on dirt – use a plywood base under the rebar cutter to keep armature and fan clean | 6 | www.bnproducts.com BN Products-USA... - Page 7 On these newer models simply rotate the Allen set screw a quarter turn to retract the piston. On the BNHC-20, see parts breakdown for the location of this release valve.
-
Page 8: Oil Level Check
7. After topping off, extract air from system. Gently tilt cutter length- wise and return it to a level position. Top off again and tilt in the op- posite direction. Repeat this process until all air has been extracted. | 8 | www.bnproducts.com BN Products-USA... -
Page 9: Carbon Brushes
WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. | 9 | www.bnproducts.com BN Products-USA... -
Page 10: Work Area Safety
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. | 10 | www.bnproducts.com BN Products-USA... - Page 11 SERVICE Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is main- tained. | 11 | www.bnproducts.com BN Products-USA...
- Page 12 For a Service Repair Center nearest you please call (800)992-3833 or go on- line www.bnproducts.com BN Products USA, LLC 3450 Sabin Brown Road Wickenburg, Arizona 85390 (800) 992-3833 or (928) 684-2813 Fax: (928) 684-7041 www.bnproducts.com | 12 | www.bnproducts.com BN Products-USA...
Need help?
Do you have a question about the BNHC-20 and is the answer not in the manual?
Questions and answers