Related Manuals for ABB FSK II +
Summary of Contents for ABB FSK II +
-
Page 1: Table Of Contents
— A B B I N T H E R A I LWAY S – M E D I U M V O LTA G E P R O D U C T S Product Family: FSK II + Operating and Maintenance Manual Table of Contents 1. - Page 2 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — — Glossary Glossary Watchdog function MABS Magnetic Actuator for Breaker and Switch Checksum Checksum of the MABS software Load break switch Circuit Breaker Central processing unit (on electronics card) Binary input...
-
Page 3: Disclaimer
ABB reserves the right to modify the product of ABB. The transfer of the document or parts described in this document in the framework of thereof to third parties is forbidden and will be... -
Page 4: Introduction
When comparable organisations ordering additional documentation, please • Safety guidelines for auxiliary and operating specify the corresponding reference number of materials the document, its revision and publication date. • Order-related specifications of ABB... -
Page 5: Product Description
A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S —... - Page 6 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 3. Product Description Caption Valve & protection for gas filling Optional cable exit Position sensors ON/OFF Manual tripping catch Heating resistance Cable exit Place for contact wear check...
- Page 7 The MABS card repeats this indication through date without the agreement of ABB. auxilliary relays so that it is available for external use.
- Page 8 Shown below is a schematic illustration of the NO changes or manipulations to the card are MABS control card with the corresponding to be performed without consultation with descriptions of the plug connectors. and confirmation from ABB KM1003 KM1005 KM1002 KM1001...
- Page 9 A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S 3.1.3.
- Page 10 The extension of the Type and the apparatus can be tripped by counter descriptions with numbers after the FSK clockwise rotation of the hand crank. designation are internal ABB descriptions and can vary from one apparatus to another. Fig. 13 Manual opening mechanism Fig.
-
Page 11: Safety Precautions
This document describes the only official secured in order to avoid unintentional procedure approved by ABB for performing operation before and during repair, which is the work described. ABB refuses all to be performed by qualified personnel. -
Page 12: Transport & Storage
PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 5. Transport & Storage On delivery of the apparatus, its condition is to be 5.1.1. Apparatus Storage Temperatures examined for transport damage. If a defect is For the apparatus, general accessories and spare observed (including damaged packaging), the parts, a storage temperature of:... - Page 13 In case of ABB being responsible for transport, the customer is required to report any damage in writing to ABB within 7 days of receipt of the goods. Damage reports are to be directed to the...
-
Page 14: Technical Data
PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 6. Technical Data 6.1. Electrical Data Pole 6.1.1. Load break switch & Circuit breaker FSK1025 Value Designation Type: 1250 Frequency 50 Hz -60Hz Operating voltage... - Page 15 A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S 6.1.2.
- Page 16 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 6. Technical Data 6.2. MABS Control Card A detailed description of the control card is provided in a separate operating manual Specifications are valid for cards in revision from and is available on special request.
- Page 17 A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S 6.2.5.
- Page 18 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 6. Technical Data 6.2.8. Dip Switches and their function The position of the dip-switches should only be read after disconnecting the power supply with subsequent complete discharge of capacitors.
- Page 19 A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S 6.2.8.3.
- Page 20 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 6. Technical Data 6.3. Weights and Dimensions 6.2.9. Jumper The position of the jumpers should only be read The weight specifications refer to the apparatus / after disconnecting the power supply with a accessories and do not include any specifications complete discharge of capacitors.
-
Page 21: Assembly & Commissioning
A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S —... - Page 22 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 7. Assembly & Commissioning 7.2.2.2. Version: Internal connection The high-voltage terminals are factory mounted. Every pole is linked to the control box with the The orientation is choosen by the customer or in “Umbilical Cord”.
- Page 23 A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S 7.3.2.
- Page 24 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 7. Assembly & Commissioning 7.3.5. Unsuccessful closing operation 7.3.8. Auxiliary Voltage Interruption (auxiliary This function is always active. It performs in case voltage for the capacitor charge) of wrong position an autotrip function.
-
Page 25: Maintenance
When the control box is not equipped execution of maintenance and repair activities, it with the switch for discharging the capacitors, is recommended to consult ABB customer service. the rapid discharing device allows the waiting time to be reduced to one minute and guarantees The intervals for inspection and maintenance are safe access to the circuits which might be live. - Page 26 PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL PRODUCT FAMILY: FSK II + - OPERATING AND MAINTENANCE MANUAL — 8. Maintenance Example: The capacitor bank with two parallel 0.1F 8.2.1. Cleaning capacitors, is typically discharged after 10 min. to If during inspections, the need for cleaning below 20V.
- Page 27 For additional advice, contact ABB. This exchange including the necessary final tests must be performed by ABB specialists at ABB. Breaking current Ia [kA Fig. 27 (wear measurement) Fig. 28...
- Page 28 (see 3.1.6). For apparatus manufactured before 2019, in case of signs of corrosion, damage or loosening it is recommended to replace this pin and the rings. Please contact ABB for service kit and instructions for this replacement.
-
Page 29: Disposal
A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S A B B I N T H E R A I LW AY S – M E D I U M V O LTA G E P R O D U C T S —... -
Page 30: Customer Service
10. Customer Service To guarantee superior customer service, it is necessary to comply with the following directions and guidelines of ABB and to thereby support the observance of the quality assurance. This concerns every case of damage or repair, without exception. -
Page 31: Troubleshooting
Ready LED goes out at the same time. Apparatus has been Signal input Y3 is configured as “Safe OFF” and CPU is defective Contact ABB switched off by signal at Y3 The “Auto-Reclose” Signal input Y6 “Lock in open“ is not active Close signal input and repeat procedure function is not executed. - Page 32 Your contact center: abb.com/contactcenters More service information: abb.com/service The data and illustrations are not binding. We reserve the right to modify the contents of this document without prior notice following technical and product developments. © Copyright 2022 ABB. All rights reserved.