GVision P15PX-L User Manual

Gvision p15px-l: user guide
Hide thumbs Also See for P15PX-L:

Advertisement

Precautions
Read all of these instructions and save them for later use.
Follow all warnings and instructions on the product.
Product
-
Do not cover or block the vent holes in the case.
-
Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots.
They may cause accident fire, electric shock or failure.
-
Disconnect the power plug from the AC outlet if you will not use it for an indefinite period
of time.
-
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks.
-
Do not touch the screen directly with your fingers. You may damage the screen, and oil
from your skin is difficult to move.
-
Do not apply pressure to the screen. The LCD is very delicate.
Power
-
Use the type of power indicated on the marking label.
Plugs
-
Do not remove any of the prongs of the monitor's three-pronged power plug.
-
Disconnect the power plug from the AC outlet under following conditions:
If you will not use it for an indefinite period time.
When the power cord or plug is damaged or frayed.
If the product does not operate normally when the operating instructions are
followed. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product
to normal operation.
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance, indicating a need for
service.
Power and extension cords
-
Do not allow anything to rest on the power cord.
-
Do not locate this product where persons will walk on the cord.
-
Use the proper power cord with correct attachment plug type. If the power source is 120 V
AC, use a power cord that has UL and C-UL approvals. If the power source is a 240 V AC
supply, use the tandem (T blade) type attachment plug with ground conductor power cord
that meets the respective European country's safety regulations, such as VDE for
Germany.
-
Do not overload wall outlets or power cords. Ensure that the total of all units plugged into
the wall outlet does not exceed 10 amperes.
-
Ensure that the total ampere ratings on all units plugged into the extension cord is not
above the cord's rating.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P15PX-L and is the answer not in the manual?

Questions and answers

Summary of Contents for GVision P15PX-L

  • Page 1 Product Do not cover or block the vent holes in the case. Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots. They may cause accident fire, electric shock or failure. Disconnect the power plug from the AC outlet if you will not use it for an indefinite period of time.
  • Page 2 If the power supply cord, which came with your monitor, is to be connected to the PC instead of the wall outlet, this equipment is to be used with UL/TÜV approved computers with receptacle rated 240V AC, 2.0A (minimum). Environment Place the monitor on a flat and leveled surface.
  • Page 3: Compliance Statement

    Notice: The use of non-shielded interface with this equipment is prohibited. If necessary, the user should consult the dealer or an experienced radio / television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful.
  • Page 4: Product Description

    It has power-saving capabilities and emits no X-ray radiation. You will certainly benefit from this monitor in lots of ways; to name some of them, comfort, safety, health, and environmental protection.
  • Page 5: Taking A Look

    Do not pour or spray any liquid directly onto the screen or case of the LCD monitor. Chemical cleaners have been reported to damage the screen or case of the LCD monitor. Taking a Look Front View 1. Power Switch Pressing this button turns the display system power on or off.
  • Page 6: Display Angle

    To Adjust the Value of the Control Option: Pressing + / - button changes the value of the selected OSD control option. After adjusting values, the monitor will automatically save the changes. NOTE The OSD screen will disappear if no input activities are detected for 10 seconds.
  • Page 7: Osd Control Options

    FREQUENCY This item is used to decrease the vertical interference. Select one display pattern from your computer. Use + and − buttons on the LCD monitor to decrease the vertical interference to get the optimal display. PHASE This item is used to decrease the horizontal interference.
  • Page 8: Power Led Display & Power Saving

    Power LED Color Green Orange * We recommend to switch off the monitor when it is not use for quite a long time. Troubleshooting The monitor does not respond after you turn on the system. Check if the Power Switch of monitor is turned on.
  • Page 9: Display Modes

    Display Modes Item Resolution Type 640X350 720X400 640X480 640X480 VESA72 640X480 VESA75 800X600 SVGA 800X600 SVGA 800X600 VESA72 800X600 VESA75 1024X768 VESA60 1024X768 VESA70 1024X768 VESA75 H. Scan V. Scan Pol. (KHz) (Hz) 31.469 70.087 + / - 31.469 70.087 - / + 31.469 59.940...
  • Page 10: Specifications

    Specifications LCD Display Display Size Pixel Pitch Display Mode Max. Resolution Contrast Ratio Brightness Response Time Display Color Viewing Angle Input Signal Video Sync Signal Connector Front Control Plug & Play Audio System (optional) Touch Panel (optional) Power Operating Conditions Temperature Humidity Altitude...
  • Page 11 Humidity Dimensions (HxWxD) Weight (Net) Certifications Specifications are subject to change without notice. WARNING Do not disassemble the monitor. Contact your dealer if needed. 10% ~ 90% (No Condensation) 408.5 x 390 x 195 mm 5.3 Kg C-UL, FCC,, CE...

Table of Contents