IMER COMBI 250 V Operating, Maintenance, Spare Parts Manual page 2

Dear Customer,
Congratulations on your choice of purchase: IMER saws are
the result of years of experience and are equipped with all the
.
latest technical innovations
- WORKING IN SAFETY.
To work in complete safety, read the following instructions
carefully before using the machine.
To work in complete safety, read the following instructions
carefully before using the machine.
This OPERATION AND MAINTENANCE manual must be kept on
site by the person in charge, e.g. the SITE FOREMAN, and
must always be available for consultation.
The manual is to be considered integral part of the machine
and must be kept for future reference until the machine is
disposed of. If the manual is damaged or lost, a replacement
may be requested from the manufacturer.
The manual contains important information regarding site
preparation, machine use, maintenance procedures, and
requests for spare parts.
Nevertheless, the installer and the operator must both have
adequate experience and knowledge of the machine prior to
use.
To guarantee complete safety of the operator, safe operation
and long life of equipment, follow the instructions in this
manual carefully, and observe all safety standards currently in
force for the prevention of accidents at work (use of safety
footwear and suitable clothing, helmets, gloves, goggles etc.).
- Make sure that all signs are legible.
- It is strictly forbidden to carry out any form of
modification to the steel structure or working parts of
the machine.
IMER INTERNATIONAL declines all responsibility for failure to
comply with laws and standards governing the use of this
equipment, in particular; improper use, defective power
supply, lack of maintenance, unauthorised modifications, and
partial or total failure to observe the instructions contained in
this manual.
IMER INTERNATIONAL reserves the right to modify features of
the saw and contents of this manual, without the obligation to
update previous machines and/or manuals.
1. TECHNICAL DATA
Technical data are stated in table 1 and electrical
specifications in table 2.
TECHNICAL DATA - Table 1
Model
Max. diamond blade diameter
Diamond blade hole diameter
Single phase motor (115V 60Hz)
output
Max. blade rotation speed (115V
60Hz )
Worktop dimensions
90° cut length (th=16mm)
Length of cuts from above
Maximum cut depth w ith single
stroke
Maximum cut depth w ith tw o strokes
Water pump flow rate
Water tank capacity
Machine dimensions
Packed machine dimensions
Weight w ith packaging
IMER U.S.A. Inc.
COMBI 250 V
P ro te c ti o n c a te g o ry
2. DESIGN STANDARDS
The saws have been designed and manufactured according
to the following european standards: EN 292-1-2; EN 60204-
1;EN 12418.
3. NOISE EMISSION LEVEL
Table 3 specifies the sound emission levels measured on the
saw
pressure level measured at the ear of the operator under no
lload conditions
SA WING MACHINE
4. GENERAL SAW DESCRIPTION
4.1 General description:
The Combi 250 V is a saw comprising the following main sub-
groups :
-
-
-
-
-
-
The cutting head is mounted on a reinforced aluminium profile
and is equipped with horizontal and vertical movement
facilities.The aluminium profile is hinged onto sheet steel arms
COMBI 250 V
(ref.H fig. 5) and the entire unit can rotate through 45° ( fig. 6)
10 inches by means of the relative handwheels (ref.L fig. 7).
The cutting surfaces are positioned on the tubular frame of the
1 inches
saw which is placed on the tank constructed in impact-
resistant plastic.
1.1 Kw
The water immersion pump is mounted below the cutting
surfaces on a special bracket and supplies a water distributor
3.400 rpm
inside the blade guard for cooling the cutting blade during
operation.
500x840 mm
The high resistance plastic handle (ref.M fig. 6), is equipped
with the main ON-OFF switch on the operator side to facilitate
660mm
saw activation and shutdown.The raised position of the red
785mm
OFF button on the handle is designed to facilitate shutdown of
the machine in the event of an emergency. The motor
66 mm
capacitor is located in a protected position inside the handle.
The saw is fitted with a guard to guarantee optimal safety
95 mm
during operation and to protect the user during cutting cycles.
A valve is mounted above the blade guard to adjust the flow
10 L/min
rate of water delivered to the cutting blade.
42 L
4.2 Processable materials:
1040x560x640mm
This saw has been designed for cutting the following
1050x570x660mm
materials: ceramic tiles, masonry and stone in general with
41 Kg
2
F e a tu r e
P o w e r (k W )
R a te d vo lta g e (V )
F re q ue n c y (H z)
A b s o rb e d c urre nt
N um b e r o f p o le s
rp m
S e rvi c e typ e
Ins u la ti o n c a te g o ry
C a p a c i to r (µ F ) 11 0 (Ø 5 0 x1 2 0 )
(Lwa)
in accordance with EN ISO 3744 and the sound
(L ) .
PA
TABLE 3
TYPE OF MOTOR
CM250 V ELETRIC
cutting head (ref. A fig.1).
sliding guide (ref. B fig.1).
water collection tank (ref. C fig.1).
frame (ref. D fig.2).
cutting surface (ref. F fig.2).
stand (ref. G fig.5).
11 5 /6 0 H z
1 .1
11 5
6 0
1 4 .4
2
3 4 0 0
S 6 4 0 %
F
IP 5 5
L L
P A WA
70 85