Related Manuals for ASUNA 7150
Summary of Contents for ASUNA 7150
- Page 1 7150 Minotaur Magnetic Commercial Indoor Cycling Bike Owner’s Manual Made in Taiwan...
-
Page 3: Table Of Contents
INDEX IMPORTANT SAFETY INFORMATION ..............1 EXPLODED DRAWING ..................... 2 PARTS LIST........................ 3 ASSEMBLY INSTRUCTION..................4-9 USER INSTRUCTION ....................10 MAINTENANCE ....................... 11 ATTENTION: Please verify that all parts associated with this product are in good condition and accounted for. During the assembly process, please be sure to follow each step accordingly, as it has been explained within this manual. -
Page 4: Important Safety Information
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. -
Page 5: Exploded Drawing
Exploded Drawing... -
Page 6: Parts List
Parts list Name QTY No. Name Seat Plastic washer Alloy bind clamp ( L ) Fixed bolt Spring Seat post Alloy bind clamp ( R ) Seat slider Washer Washer L-Shaped Knob 1 Belt Crank bolt Spring Outer chain guard bolt Washer Outer chain guard bolt M5 Bolt... -
Page 7: Assembly Instruction
Assembly Instruction STEP 1: Attach the Front Stabilizer (No. 18) and the Rear Stabilizer (No. 14) to the Main Frame (Y) using 4 Bolts (No. 10), 4 Washers (No. 9) and 4 Nuts (No. 8). Tighten and secure using spanner wrench. - Page 8 Assembly Instruction STEP 2: Loosen L-Shaped Knob 1 (No. 6) on main frame handlebar tube to remove insert protect cap, then insert the Handlebar Post (No. 22) into the handlebar tube of the Main Frame (Y). Adjust Handlebar Post (No. 22) to the desired height. Tighten the L- Shaped Knob 1 (No.
- Page 9 Assembly Instruction STEP 3: Insert the Seat Post (No. 42) into the seat tube located on the Main Frame (Y). Insert the Seat Slider (No. 43) into the Seat Post (No. 42). Tighten the L-Shaped Knob 1 (No. 6) to secure the Seat Slider (No. 43) in place. Secure the Seat (No.
- Page 10 Assembly Instruction STEP 4: IMPORTANT: Read instructions carefully, failure to do so may cause permanent damage to your bike. Connect Pedals (No. 11) onto the Left and Right Crank Arms (No. 20 and No. 21). (Before you begin, immobilize the crank arms by turning the tension control knob all the way to the right).
- Page 11 Assembly is complete!
- Page 12 Before beginning use of equipment, please be sure to inspect the entire bike carefully. Ensure that all moving and stationary parts have been properly installed and are operational. Inspect all screws, nuts and bolts as well to make sure that they are tightened and secure. MOVING There are Transportation Wheels (No.
-
Page 13: User Instruction
User Instruction ASSEMBLY Properly assembling the equipment before use is very important. Be sure to follow all instructions as detailed in the assembly instructions section of the owner’s manual. ADJUSTING THE RESISTANCE Adjust the resistance of the bike using the Tension Knob (No. 24). Increase the level of resistance by turning the tension knob to the RIGHT, and decrease the level of resistance by turning the tension knob to the LEFT. -
Page 14: Maintenance
Maintenance IMPORTANT: Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to ensure that the equipment is maintained regularly. Any components found to be worn and/or damaged should be replaced before continuing use of the equipment.
Need help?
Do you have a question about the 7150 and is the answer not in the manual?
Questions and answers