Lanex XPTU420 Instruction Manual

a full body harness complied with EN 361 is the only acceptable body holding device that can be used in a fall arrest system.
!
! the anchor device or anchor point for the fall arrest system should always be positioned, and the work carried out in such a way, as to minimise both the potential for falls
and potential fall distance. The anchor device/point should be placed above the position of the user . The shape and construction of the anchor device/point shall not
allowed to self-acting disconnection of the equipment. Minimal static strength of the anchor device/point is 12 kN. It is recommended to use certified and marked structural
anchor point complied with EN795.
! it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system, so that, in the case of a fall, there will
be no collision with the ground or other obstacle in the fall path. The required value of the free space should be taken from instruction manual of used equipment.
! there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed during equipment utilization,
especially:
- trailing or looping of lanyards or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
! personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of steel or plastic) to protect it against
damage or moisture.
! the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use mild detergents for delicate
fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the equipment gets wet, either from being in use or during
cleaning, it shall be allowed to dry naturally, and should be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly
slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
! personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation, damp environment, sharp edges,
extreme temperatures and corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
LANEX Hluèínská 1 / 96, 747 23 Bolatice, Tel: + 420 553 751 111, Fax:: + 420 553 654 125, E-mail: lanex@lanex.cz, www.lanex.cz
,
DATE OF MANUF.
DATE OF PUTTING INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
Instruction Manual
READ CAREFULLY BEFORE USE
WARNING: Any activities at height are considered dangerous and may result in serious injuries or even death.
The person using this equipment is responsible for any possible damage or consequences of an accident.
1. Definitions
WLL – Working Load Limit
MBS – Minimum Breaking Strength
DF – Design Factor
2. Basic parameters of the device
TECHNICAL DATA
KIND OF PULLEY
Max. diameter of rope
Material
Working Load Limit
Minimum Breaking Strength
Safety Factor
Weight of the set (without the lanyard)
MARKING
XPTU421
PERIODIC
EXAMINATION
NEXT DUE DATE
THE EQUIPMENT
PULLEY XPTU420 XPTU421
Ref.: XPTU420 / XPTU421
EN 12278
XPTU420
Ø13,5 mm
aluminium/stainless steel
500 kg
25 kN
1:5
95 g
number/year of the European
standard the equipment conform
admissible lanyard parameters
month/year of the device
manufacture
caution: read the manual
permissible load direction
permissible working load
XPTU421
Ø13,5 mm
aluminium/stainless steel
500 kg
25 kN
1:5
135 g
XPTU420